Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original bake element had open circuited, fortunately the day after Thanksgiving and not on Thanksgiving
Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reconnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.
I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.
Ordered element and received it the next day. Removed two screws that holds element in place. I then pulled the element out about 3 or 4 inches and disconnected the two wires. Put new element in connected the wires mounted element in place with the two screws. Now works great!
Unplug first then took back off and took wire clips off and connectected the other on in worked fine you will like part select I just ordered apart for my frig. Waiting for it now.
The upper broiler element had burnt and broken into.
I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, Removed the old element and installed the new one
Two screws held the element in place, removed the screws and pulled the piece out. Back of piece has two wires attached, unplug them then attach the new element and replace the two screws to remount. First make sure the breaker to the range is turned off before starting the repair.
First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.
simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.
Removed 3 screws on bottom edge of door,2 screws on top edge of door. Outside of door comes off. Then use a 1/4 nut driver and remove glass window supports until you get to the inner door glass. Reverse to assemble. Gasket was okey.
Take the time to pull off the door from the hinge; which is to simply pull it up to release with the door open approx. 4 inches. Have a Philips head screwdriver and a nut driver set available. Keep the screws grouped and the take it apart in the logical sequence. It took about 30 minutes total to complete the job. But then again, it was a woman who did it!
Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.
First I removed the bottom oven drawer from the stove. Then I removed all the screws from the outer oven door. Then I removed the screws from the inter door panel and needed assistance to remove the first glass panel and frame. Then I removed the second panel of glass and frame. Then I removed the third panel of glass that was broken. The gasket was the last part to be removed. Getting the new gasket to stay put while putting the new glass panel next to it was the hard part. I needed assistance to place the glass against the gasket and then place the frame back on this panel. Once this mission was accomplished. It was a matter of getting the next glass panel put back in the frame. and replacing the inter door panel and putting the screws back in. Then I put the third glass panel and screws back in. Once this was accomplished , I put the outer door back and put the screens back in the outer door.