Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.
You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.
If it wasn't for that minor slowdown it would be a five minute job.
Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.
broke tab that holds pantry lid; something fell on the pantry lid and cracked the clear section of lid
The parts arrived VERY quickly.Replacement was extremely easy even though the right side end cap has the temperature adjustment it only took 15-20 minutes.
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Our refrigerator was too cold as the thermistor seems to have gone
It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.
Removed drawers and glass top and support bars Two screws on slid bar two screws on end cap, Make sure you take time to remove air control it has two pivot points with small taps. Then just replace parts as you had taken off very easy.
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
Wife learned you can overload the cheese and fresh veggie trays and the plastic rails broke. Repair required removing parts from the old crisper frame -- no experience and no instructions. Had to study broken part and figure out how to remove parts. Released catches with a knife and, by trial and error, figured out how to install rescued components on new crisper frame with minor damage and frustration.
Weak water delivery to water dispenser and ice maker and loud thumping sound.
Gain access to rear of refrigerator. Use protective board to prevent marring floor. Unplug refrigerator. Turn off water supply and depressurize line. Remove old water filter head. Disconnect filter head inlet water supply line located behind the refrigerator. Disconnect the filter head filtered water return line at the water valve. From refrigerator interior, disconnect the lower filter water cover. Press the outer cover away from filter head until one end is free of the water filter head tang and remove cover from second tang. Push the Styrofoam "block fill" toward the rear of the refrigerator to remove it. If you try to remove this from the outside by pulling it, it will likely break. Pull water filter head assembly to remove it. Install new part by reversing the steps.