59669872990 Amana Refrigerator - Instructions

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

First I had to determine what was wrong. Obviously the compressor was working since the freezer was cold. Digging for awhile revealed that the evaporator coils for the freezer had frozen up into a solid block of ice. Then I had to figure out why. Tested the defrost heater in place--small resistance (~3 ohms), OK. Removed and tested the timer--unsure. Removed and tested the defrost thermostat--did not turn on when plunged in ice water or frozen with canned air (turn the can upside down--be careful!, you can instantly freeze-burn your skin), bad. Chose to purchase and replace both the timer and the thermostat. Took the opportunity to THOROUGHLY clean everything, front, back, and underneath. Found the drip tray transition piping cracked at the junction and replaced it with a cut-off funnel "glued" into place and to the underside piping with the RTV Silicone. When parts arrived, tested them and confirmed that the original timer was OK and the thermostat was bad. Installed the new thermostat (and went ahead and installed the new timer). NOTE: one connector on the thermostat was not identical to the orginal equipment. Rather than cut the refrig wiring, I chose to build a jumper with the original connector on one end and a new one for the new thermostat on the other. Buttoned everything back up, re-leveled it, and let it run for 24 hours at the manufacturer's recommended "first" settings (4 and 4) without being disturbed. Seemed fine, loaded it with food, everything is great including non-frozen veggies! (I suspect the ice was forming frequently and blocking the return from the refrig compartment, which is right next to the veggie drawer.)

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Had to remove screws inside back of freezer panel, took off old thermostat. This one had a different plug on the end that wasn't compatible, so had to cut that off and wire it to the old plug end. Piece of cake. Put back panel back on and back in business. Hardest thing was getting the screws out!

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00

I removed about 25 nuts from the door which held the inside panel in place. Then I removed the old gasket and placed the new one, making sure it was fitting correctly. I replaced the 25 nuts and the door was ready to go. I had to tape the door shut for a couple days so the new gasket could wear in. It took about 15 min.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Removed ice maker, then rear panel of freezer compartment. Removed old evaporator fan, cutting tie wraps as required.

Replace evaporator fan assy, paying attention to wire harness routing and secure harness with tie wraps.
Reinstall rear panel of freezer compartment. Re-install icemaker.

Turn freezer section control wheel off, unplug unit. Then remove all items/baskets from freezer to allow access. Use nut driver to unscrew 3 screws on control plastic housing. Drop down housing from top and unplug wires (note correct locations) from control wheel switch. Remove screws and ground wire from metal backing plate to plastic housing. Push or pry the 2 metal holdtabs down carefully to allow the 2 plastic housing tab fingers to be pushed inwards to seperate metal plate from housing. Pry control wheel off from switch arm with screwdriver. Remove switch and replace with new one.
Use the reverse order of removal above to replace into freezer but use caution when replacing wheel onto switch arm and plugging in wires. Remember to carefully pry the 2 metal tabs back up to secure the plastic finger tabs in place.
Job done.

First step, call the repair man. He listened, and then said to get a new refrigerator, since this one is 28 years old and the repairs could amount to a significant part of the price to buy new. Even if he fixed this, it could develop other problems, yada. So we went out to buy and discovered nothing suitable that would fit in that slot of our kitchen! We'd need new counter top and cabinets to fix this problem! So we went to the Internet and searched to find the likely source of the problem and the parts schematic at PartsSelect.com. Yah! We ordered the part, and then found we had no idea how to install it. Sooo, back to the Internet, and eventually got some good clues - it goes in the kick space under the front, and just plugs in, once you can get to it by removing the bracket that holds it. Working underneath a refrigerator is not complicated but it's awkward. The form of the new timer was not exactly the same, but it does function correctly. We have no experience whatsoever with appliance repair, so pretty amazed at our success. This old Amana looks very good inside and out and is now working perfectly again. If it lasts a few more years, we will be thrilled to have spent $15 to save $500. We can always buy new later on.