58635 Refrigerator - Instructions

I saw on a partselect web site that these symptoms could be caused by a failed condensor fan motor. After removing the cardboard panel in back of the refrigerator I noticed the fan was not running when the rfigerator was. The fan was held in place by three brackets. I unscrewed the screws holding the fan motor to the brackets and also unscrewed one of the brackets to make room to pull the motor out. I cut the wires close to the motor. I removed the fan blade and secured it to the new motor. I had to reroute the old wires in order to have enough slack to use wire nuts to attach them to the leads on the new motor. I then re-attached the motor to the two brackets remaining in place and then re-attacehed the third bracket I had removed to get the motor out.. The most difficult part was working in a very confined space.

After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.

I was not sure what the fix was on my refrig, so I ordered the defrost timer kit, bimetal defrost thermostat, and the evaporator heater(about 100.00 in parts)
I think my entire problem was the bimetal defrost thermostat, as it was somewhat bulged out on the plastic side.
The evaporator coils would freeze over--the evap. fan would not work and the cold water dispenser would not work. I did't have time to just replace one part at a time so I ordered all three parts that have to do with the defrosting of the evap. coils.
The parts worked and the refrig. is operating fine. Thanks to parts select for a super fast delivery(one day).

First of all, I do not have a history of repairing appliances or even the knowledge of what all the parts are named or how it all works. That said, please excuse my other than technical explanation of the repair. After reading a few posts, I decided to order the two parts and give it a try. The Defrost timer was easy to remove - two screws to remove the housing and two screws to remove the timer. The bimetal defrost thermostat was an easy installation - after removing the cover plate (back of freezer section) I removed the two wire caps that was connecting the existing thermostat to whatever it connects to - I guess the heating element and ? I was a little confused because the replacement thermostat had more wires that the existing one. I decided to cut away the extra wires and connect it just like the old one was connected. I didn't work at first and I was about to call in a pro. I turned the defrost timer knob and everything started to work. It has worked beautifully since and I got to brag a little to my wife - that was short lived because she reminded me of the other "stuff" that needed to be fixed! Thanks to the folks that posted before me - it helped me understand the problem and the repair.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

First I removed the knobs, then the plastic cover over the thermostat. Then, I removed the two screws that hold it on. I removed the thermostat, unplugged the electrical leads, and pulled out the old thermostat. I then inserted the new one, hooked up the leads and reassembled.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

the problem was the evaporator has frozen causing the water line to freeze also.
I opened the cover to see the evaporator, verify it was frozen, try to unplug and let it thaw, but it would freeze again. Thought the defrost thermostat was not working but did not verify, order new one and replaced; it did not work. After a long time of experimenting different things I found out that the defrost thermostat was supposed to be clamp to the line. It was not clamped to the line, was just hangin from its wires when I found it. So.....it works now!!! but I don't know what happen in the first place: the clamp fell off, or did it come from mgfr unclamped but happen to work since it was cold new, now getting old and not cold enough to close the thermostat unless on the line? anyway, it works and I decided to keep the part for spare. Hope this help someone else!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

Removed the back wall (several screws) of the freezer too get at the thermostat and removed the thermostat and after checking to makes sure I plugged the wires in correctly I replaced the defrost timer by removing the housing that held it in place, which was located underneath the freezer compartment on outside of the unit. That was it!

I unplugged the unit, removed the freezer racks and removed the back panel to expose the evaporator. I removed the defrost thermostat, unplugged the wires, and installed the new thermostat. I replaced the panel and racks then removed the defrost timer kit by removing the two screws that fastened the cover to the refrigerator and the two screws that secured the timer to the cover. The timer is centered behind the front toe grille assembly. I installed the new timer, replaced the cover, and plugged the refrigerator in. It took several minutes for the defrost timer to advance before the evaporator fan would come on.

Removed door. Removed old cam closure assembly. Noticed that there was almost nothing inside the door for screw to screw into(only styrofoam insulation), which is why original screw backed out. Bad design. Got longer screw at bigger diameter. Pushed high strength glue into hole, on screw threads, and underneath screw head. Assembled. Crossed fingers. About three weeks have passed and so far, so good.

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.