Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gear noise whining
Took the mixer apart many times. Grease all over the place. put new gears in still noisy. The worm gear must have been cut wrong. The noise still there. The part select sent out a new worm gear. I did not put it in yet. I put the old worm gear in and the noise stopped even though it shows wear. Have not decided whether I will put it in yet.I would also like to add that the people that I talked to at the this site were very very helpful and great just great---------
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Researched the internet for a diagram of the mixer and used that to take it apart, clean everything, then install the new gear and new grease. Works great so far.
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Removed the top housing. Visual inspection revealed a cracked gear housing. Removed the 4 screws to remove the housing. Removed the gear retaining clip and inspected the gears and pin. The housing was the only problem. Noticed the plastic housing locating pins were missing and were stuck in the bottom aluminum housing pin receptacles. Carefully drilled out and cleaned debris. Installed the new gear housing with gasket. Tested the machine then replaced the top housing.
Broken thrust bearing kit caused damage to the worn gear
Disassambled the gear-train.Removed all broken pieces and grease from gear case. Cleaned gear case and all parts. Reassembled gear-train with new parts and packed all with suitable quantity of new grease. Test run with variable speeds assuming working smoothly.
Last repairperson broke the top cover of the gearcase ; still need this part .
Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
The stand mixer would not rotate at low speed. Upon disassembly found one of the two alignment pins of the upper gear case broken.
1. Removed the decorative band then the upper motor cover. 2. Removed the upper gear case cover. Found one of the two alignment pins broken. 3. Inspected gears. 4. Cleaned out old grease. 5. Repacked with new food grade grease. 6. Reassembled.
Board fails, causing motor runs at high speed only
3d time in 20 years, but the mixer itself is built like they did 20 yrs ago PartSelect had the part in my mail box in *20 hours* from online order! See https://www.ereplacementparts.com/kitchenaid-4kp26m1xmc4-professional-stand-mixer-parts-c-114958_114959_115101.html for instructions. BUT - they changed the design so a power switch previously separate from (to the left of) the circuit board is now a microswitch integrated on the board, leaving you with ONE LESS WIRE. Attached is the fix diagram & directions for the new design.
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover. Reassembled mixer.