4KNTW5705TQ0 Amana Washer - Instructions

Removed control assembly found lid switch. Had to unscrew ground wire from warsher popped clip on old switch came right out. Had to play with lid in order to remove. Popped new switch in screwed ground wire. Reinstalled control panel,plugged in and the way it went. Trouble shot with parts direct made it easy and saved me 350 dollars(new washer)

1. Removed back panel.
2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor.
3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly.
4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off.
4. From bottom of unit disconnected motor/transmission unit from wash tub.
5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one.
------------------------------------------------------------
Steps 1 thru 3 were unnecessary.
All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.

Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points.
Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time.
Forgot to order suspension spring clips, order them next day shipping came the next day .
Just because parts are in stock doesn't mean you will receive in a timely fashion if you need parts better order next day freight.
Videos, parts diagrams and instruction are great, regular freight is not good

Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!

Second time I did this. Same repair about 4 years ago. Pretty easy. Take the cabinet enclosure off, take pump off, remove motor and replace the coupling. Since the coupling is now reinforced with metal, a little more difficult to get on the drive shafts of the motor and the clutch drive?. $20.00 saved me $500.00 for now with a relatively easy repair and hopefully with reinforced part, it will last a little longer.

Turn off the power,remove the washer cabinet top and side panels. unsnap the water pump clips, unscrew and unclip the motor mounting clips.Remove the old drive coupling and triangular drive shaft adaptors.Clean area and install the three new parts, reattach the motor and pump, close the cabinet,turn the power back on and test.Done! The only hard part is working down on the floor and you need a good flashlight.

snapped off the 2 springs on the water pump,took off hoses with pliers,took off the 2 little screws on the motor springs.snapped off the 2 springs on the motor,and the motor came off.took out the drive coupling,it just slides off...then reverse the procedure,and you are done...

I read the experiences of others on this site and determined that the problem was probably the lid switch. Used others experience in taking the panel off and removed the old switch and inserted the new one. The post to be sure to have the lid open was good and probably saved me some time. Overall, the fix was simple and the problem appears to have been solved. The lid switch got here the day after I ordered it and that was great service. Better than paying for a service call or new washer.

Removing top console control panel, deataching 2 clips and removiong the entire box to get access to the agitator and the direct drive, one part on the top and other on the bottom of the washer,removing top cap of the spinner got access to the agitator. Using 1/2" socked and pliers remove & rep[lace the agitator. for the direct coupling: remove the water pump (2 clips) 1/4" socked & screw driver remove the electrical Motor, remove & replace the direct coupling, put all removed parts back toguether, reasembly the box ataching clips on place, console panel Install, perform operational check, was good I have the washer running like a new machine.

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .

Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowly rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....

Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!

I actually didn't remove any of the panels. I tipped the washer at a 45 degree angle to the back and side to release the motor clamps, unhooked the power to the motor and removed the two drain pipes from the motor.

Once I had all of that removed, I was able to pull the motor away from the transmission and put the new coupling pieces on. The hardest part was holding the motor up (it is fairly heavy and cumbersome to hold while the machine is tipped like that). The pieces didn't go on too easily either. It would have been ideal to have at least the front panel off to use a hammer more easily. I did manage to get it on using a socket and a hammer. With some light taps it went on.

Next I put the hoses back on, the power, the bottom motor clamp, and then wrestled for another 30 minutes getting the top motor clamp on.

The clamps are the metal like springs that hook into the transmission and then spring tighten the motor to the transmission. Then there is a little screw that holds it in place... Not easy to see from any angle, and that is where having the front panel off would be ideal.

I've NEVER worked on a washer before and I accomplished this by myself in about 2 hours. I think if you are sure this is the problem, fix it yourself. Best 20 bucks and 2 hours I spent this month by saving a couple hundred on a new washer or repair person.

I removed four srews holding the control panel and laid it to the side, then removed a screw holding the ground on and disconnected the electrical connection. The lid needs to be open to remove the switch. Just remove the switch and reverse sequence. To replace the coupling , I laid over the washer and removed two screws holding the straps connecting the motor to the transmission. After seperating, I pulled off old couplings and reinstalled the new ones on both the motor and transmission. I had to tap couplings on. Then reversed the installation and set backup and tried it out. It worked great.

Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.