Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not fill
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
the magnetic door plunger fell on the floor, would not stay in place and did not hold the door closed. Received a new on, put it in place. works just like it is supposed to. took all of 2 seconds. great service from Partselect. got the new part in less than a week.
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Cold water inlet valve was leaking where solenoid attaches to valve body.
Hardest part of the job was getting the washer away from the wall. :) Disconnect power & water Remove top panel, two screws at back Remove two screws holding valve to washer body Use pliers to loosen and pull back spring clamps on three water tubes Remove tubes by twisting and pulling Reverse process to install new valve.
I am convinced that the original valve began leaking because I had heard water hammer for years as that valve opened and closed during operation. I bought two water hammer arrestors (less than $30) that attach inline with the inlet hoses and I think that will prevent the problem from recurring.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
1. Unplugged electric chord from wall. 2. Pulled washer out into open area to get behind it. 3. Turned off hot and cold water faucets 4. Used channel locks to remove hot water and cold water hoses from back of washer. Dropping hose into a bucket to catch water from hose. 5. Removed screws (Phillips screw driver) holding top to back of washer. 6. Pulled back on the top and lifted off washer. 7. Arranged new intake valve to mock location and setting of old intake valve. 8. Using Phillip screw driver, unscrewed old intake valve from back of washer. 9. Unconnected wiring from old intake valve. These were easily identified and not needed to mark left right center. 10. Using pliers, pinched hose clips and moved to middle of the hose. Did this for all 3 hoses. 11. Removed hose from old intake and connected to same location on new intake. Repeated for all 3 hoses. 12. Using pliers, pinched the clips and moved to the end of the new intake valve. Did the for all 3 hoses. 13. Using Phillips screw driver, screwed in the new intake valve where the old intake valve was located. 15. Inserted the wiring connects into new intake valve. 16. Reconnected water hoses back into washer machine (after inspecting and cleaning plastic strainer traps) 17. Turned on water faucets 18. Plugged in washer. 19. Ran an empty load for a cycle. 20. Did not fail. 21. Reattached top to washer. Laying down an inch from front and push forward to hear a click or lock. Then screwed in the 2 screws. 22. Pushed washer back into original location.
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here