41790802991 Kenmore Washer Dryer Combo - Instructions

First I read the manual on how to replaced the dryer drum belt. Second I took off the front panel. This would involving taken all screws from the top of the dryer face and the front panel. Thirdly I removed the exhaust attachment. Then I saw that the belt broke. Really it looked torned apart. I believe too heavy of a load in dryer. I then installed the new belt and reversed everyhing I did to start. The dryer runs great. This is not that bad of a job. If you can do it yourself, why pay hunreds on a service man to do the job.

I contacted a company to come out and diagnose the problem. They informed me that the thermal limiter is bad and needed to be replaced for $15 for the part and $85 labor. I found the part on this site for about $10, and did the repair myself. The dryer was mostly dismantled so I pulled the drum back, and replaced the part. The tricky part was the pulley system was, so make sure you see it before hand or find a diagram online. Once that was figured out, I set the drum back up, greased and tightened the pulley, reattached the front of the washer with connections, and closed the lid.

removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve was made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.

After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

removed old agitator by loosing a bolt at top, after removing the detergent dispenser. agitator came off easily, new one on, bolt on with rachet wrench, dispencer on. works like new. thanks for the great service. the part came in faster than i thought it would, and i would have had to travel for miles to get a part around here. VAL

S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

I removed the broken knob from the metal shaft with a pair of pliers and slid the new knob in place.

Piece of cake!

I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, the machine ran as quiet as it did when I first bought it.

I installed this part on a stackable washer-dryer unit. First, I removed the hoses (one had broken off already, damaging the cold water coupling). Using a nut driver I removed the screws on both L-brackets in back that help secure the dryer unit to the washer base. Then, I located 2 other screws securing the dryer to the washer base. These were fairly accessible in the recess where the dryer exhaust vent is located, directly above the water inlet valve. I removed both with a nut driver. I thought I would have to also unscrew 2 more screws on the other side of the dryer, but these were not accessible. So I lifted the side of the dryer I had unbolted to get to the water inlet valve. And voila! It lifted up. I placed a 2x4 on edge to keep the dryer tilted open. The inlet valve is attached to the back inside of the washer by a single screw on the Kenmore, which I removed with a phillips screw driver. Reaching inside the back of the washer, I disconnected the water hose by pinching the retaining clip with pliers. Then I pulled the electrical connections off the the hot and cold solenoids and the unit came out. The replacement unit was installed in reverse.

Unpluged the dryer, took out the light assembly, unpluged the wires to the unit, replaced the old unit with new unit from Partselect.
Plugged dryer in, problem fixed.
Taa Daa

Thanks, PARTSELECT.

That saved me about $50.00 YAHOO!!

Removed the top of agitato removed bolt, R&R part ,put bolt an top back 3min. Top

I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!

I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and limiter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.