Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lound noise inside dryer
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room. 2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end. 3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where. 4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver. 5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place. 6. look in the drum and there is 3 screws that form a triangle shape. remove the screws. 7. remove the belt from the drum. inspect the belt. replace if necessary. 8. lift up and pull out the drum. 9. remove the rear drum assembly and replace it with the new parts. 10. repeat in reverse and your done. It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Dryer would not turn on, no power. Since i already have replaced thermal limiter switch, i knew exactly what to do and also how to shorten installation
Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
No Heat, Dryer Runs, But Right Side Of Timer Would Not Advance, Left Timer Would
I used the percentage scale on this website to try and determine the likely cause. After reading several sites, I couldn't make sense of the timer not working on just one type cycle. When I got the dryer drum off, I could plainly see that one of the heater coils was broken. They get heat stressed and break down over time and a hard shake probably finished this off. This unit is 5 plus years old. It was Saturday and I had no heater, so I actually found it at a local parts supplier. Also replaced the drum bearing and the bearing cup in the rear along with the heater. BTW, a new heater comes with a HIGH thermal switch attached to it so don't buy it extra. The bearing cone also comes with a new bushing in the pack. I DID use the Thermal Limiter that I order from the site because I was already in there. Everything works great now. I may have gotten most off my parts elsewhere but this site was the biggest help of them all. I will definitely be back here again.
Main problem was the bearing, replaced the belt and felt seal as well The video instruction was very helpful Was easy with basic mechanical aptitude Dryer running great now All parts from Partselect.com Have ordered from them before and would order from them again
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!
Called a repair co. Said it would be about a week before he came to the rural area my mom lives and he probably wouldn't have the part. He would order it after he determined the problem. So I went to your web site and ordered the item it said was 80% and two other parts just in case. He came and used the Heating Element Assembly and said it was a good thing we had it. He would have had to order it and come back probably a week later. THANK YOU!! WE needed the dryer repaired sooner and saved another service call. I am returning the other parts not used and you make it so easy to do. I plan on using your site again.
Ordered in new Element. (took apart dryer first and verified the coil on the old element was broken).
-Disconnected power -Used flat blade screw driver and popped the top of the dryer off (two clips at front of the dryer on the door piece). Pull lid back and it will rest on its own. -Removed two screws on the inside of the front door panel then used flat blade to pop four clips off. Lift up then out to removed door panel, drum will fall down. -Removed small white plastic rest from front frame. -Removed back silver vent to access motor. Pull the belt tensor away from assembly and pull belt out. -Remove drum by grabbing belt and front of drum and forcing it up until it releases from the ball housing. Slide drum out of the front of frame/dryer. -From here you can see the heating element. disconnect the coil wires (pull them). These are in series so it doesn't matter how they go back on. Disconnect the thermostat wires (X is negative lead). -Removed the four screws from the back of the dryer to disengaged the element. Removed. -Reassemble backwards.