41729052990 Kenmore Washer - Instructions

First I pulled the front panel on the washer off, than I unplugged the wires to the pump, took the two screws out that hold the pump, took the two hose clamps off and took it out. To replace I did the reverse.

First I tried to unscrew the two screws holding the latch with a phillips screwdriver. When it wanted to slip, I took a closer look at the screw heads and saw they were square drive. I got the proper tool and removed the screws, replaced the latch and replaced the screws in a few minutes.

took off 2 screws and 2 hose clamps put in new part. Put srews and clamp back on less than ten minutes. total cost with shipping $62.00. repair person wanted $265.00.

The local appliance repair store quoted me $80+ for a "kit" to repair the door catch. I saw the part on your website for less than $8. Even with rushed shipping (I have four boys who generate lots of laundry), it was only about $20 total. You guys are AWESOME! I sell tools for women and do-it-yourselfers and am directing my customers to your site. Thank you!!!

Let's see...removed lower panel-used tools to unscrew the unit---one piece-nice to replace---EASY to replace! Removed hose---placed hose on new unit; screwed all back to bottom of washer-replaced lower panel...Voila! Made sure unit was balanced...did a load of whites---Awesome WASHER NOW!!!

remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.

The wind blew the washing machine door shut so hard that the catch snapped in half. I found Part Select dot com on the internet, ordered the part and within a couple of days, it arrived. I didn't even do the repair...my Fiancé did it while I was away at a conference. Easy to fix, great ease of finding the part on Part Select...saved the labor of having a repairman come out to fix it. When in doubt, Do It Yourself!

Removed spring retainer straps from top of springs. Propped up tub with blocks and a wedge. Lifted out each spring and replaced. Re-attached spring retainer straps. Removed pins from shock absorbers (old/broken ones). These break due to moving washer w/out installing original foam blocks and support screws or due to age and fatigue. Pins have a retainer that must be depressed as you pull or push them out. may need to spin back and forth with pliers as you pull them. Bottom right pin won't come out w/out a hassle. Cut it in pieces with dykes and used spare pushed in from the FRONT (not the rear, as it was originally installed). Found leak was not fixed by getting the drum back up to proper height. Found bolt on tub had broken the bottom of the soap dispenser "tray". This is a 50.00 part. Made a patch from the bottom. Roughed up plastic and used silicone adhesive. After it had adhered filled from top with more silicone. Allowed 24 hrs to dry. Washer is as good as new.

"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.

Replaced both the water inlet valve and the tank pressure switch to eliminate any possible cause. The repair was easy, and now the washer works fine.

PartSelect is fantastic. Door catch broke on 3 day holiday weekend and given age of washer figured nobody would have the parts. Found PartSelect on line, ordered, paid for expedited shipping, got the part by the end of the week. Took me just a few minutes to screw in the catch and I was doing laundry again the same day. Had a little bit of a problem identifying the part on the schematics but once I figured it out everything was a breeze. Recommend PartSelect highly.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

Remove front panel to expose shocks. It took some time to remove the old shocks, both were broken. The pins were somewhat difficult to reach and remove, especially the one on right for it was shoved up against the electric wiring box. We ended up putting that pin in backwards for the new shock because it was impossible to reach from rear. Putting the new shocks was easy it was removing the old ones that took most of the time. The washing machine is working perfectly now.

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!