3ET22DKXWN00 Whirlpool Refrigerator - Instructions

First I entered my model #, then picked the symptom, then went with the odds when presented with the likely suspects. The run capacitor, and bi-metal defrost timer had the highest % of guilt. Most of the time was spent defrosting the coils with a hair dryer. The run capacitor took 3 minutes to remove and replace. I snipped out the old defrost timer and used butt connectors to wire up the new one. The old timer flunked the continuity test when placed in salted ice water. The freezer/fridge runs like new, for about $66. The run capacitor was probably ok but I left the new one in, being too lazy to send it back. "Part Select" was a great partner in helping to fix my machine.

My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's working fine now and I'm a satisfied customer!

Took the old fan out and put the new fan in.

opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

Snapped in new end caps and attahed existing shelf bar. Have done this twice. We tend to stuff too many items on that bottom shelf.

I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.

Moved fridge out from wall, unplugged power cord. Laid on floor, removed 6 screws from cover. Removed one threaded bolt to allow assembly to slide out. Removed special nut, and took fan off. Removed 3 motor mounting bolts. Unscrewed 2 wire nuts, and untwisted wires. (option 1, no ground) Vacuumed entire area around motor. Used 3 bolts to mount motor to holder assembly, and special nut to install fan. Stripped wires back about 3/4 inch. Twisted two wires together CW, and installed new wire nuts. Slid motor assembly back into slot,(keep wires away from blades) and used one threaded bolt to secure assembly. Reinstalled cover plate with 6 screws. Plugged power cord in to test air flow (out through cover vents). Moved fridge back into place. The loud whirring noise did not stop for a day; then quiet!

I was pleased with the new ice maker and how soon I received it. I was disappointed because there were NO installation instructions that came with it. There were only service instructions that came with it. I contacted partselect and was told that they get the part from whirlpool and they are responsible for everything and was given a phone number to call. I called Whirlpool and was informed that they don't provide installation instructions, I said that on the web page is boldly displayed an installation instruction sheet. Whirlpool said that they expect that the installation person knows what they are doing. I let it go and was very careful taking the old one out and installing the new ice maker and the new pump.

I used a socket and ratchet to back out part way the screws holding the seal. There are 4 pieces of metal strips that the screws go through to hold the seal on. Don't remove the screws completely or the plastic panel of the door will fall or come off. Take the new door seal and power it with baby power. This will help make the seal not hang up when you close the door. Now, shake off excess powder outside and then begin to install the seal. Start at the top left or right corner and work across pushing the lip of the seal into the recess of the metal strip. You will want to tighten some of the screws as you go but leave enough looseness to push the seal into the strip's recess. Proceed down each side and the bottom last. I should note that you could remove the door first and you wouldn't have to stand on your head to screw in the bottom of the seal.