3ET18DKXAW00 Whirlpool Refrigerator - Instructions

After watching the video it was a snap. Defrosting the freezer took the longest time. I used a hair dryer to melt the ice. Once the freezer compartment was clear of ice the removal and installation were a step by step procedure which the video showed in detail. It's been about a week since I installed the bimetal defrost thermostat and it seems to be working like new. Sure glad I researched this problem on the internet instead of calling a very expensive repairman! Thanks partselect. Com!!!

Removed correct part from those provided and slipped it into position. No tools necessary.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

It was an easy repair. The side hinge plate had two fasteners on it. One which was hooked shaped and the other was pointed. I took the plate and installed the hooked shaped fastener first into the rectangular cutout and then pushed the plate with the pointed fastener into the circle cutout. Checked to see if the plate was fastened and once it was the repair was done.

UN plugged refrigerator,waited 24 hours to let defrost,removed panels,cut out old Bi metal Defrost thermostat,wired in new thermostat,reassembled freezer,plug back in,working great

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

repair went well. Ice maker still not making ice. UGH

I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the new fill tube, tighten-up, good-to-go.

followed the video instruction from part select web site

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

Cover the entire metal retainer bar in painter's tape (the blue one) and use a 20-22" hacksaw to cut it to the correct length, going very slowly in your sawing.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck