37H-42T-EV ((B1X)) Maytag Range - Instructions

Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

the part arrived in two days. Just had to remove the old one and pop in the new one and it was that easy. I was amazed at how soon the part was delivered and happy to have a working burner again.

I ordered the 2 burners that were not working. When I got the burners, I discovered that one of the burners was still working and the wiring under that on had burned out. So I ordered the little box kit and repaired it. I only needed to strip wires and twist together and replace the small box. Now all are working and I am cooking with all four burners again. All for about $50.

Since it was a plug-in burner, only needed to pull it out and put the other one in.

Another thing I would like to say is that I was very well pleased with the service from partselect.com. I was unable to find the burners in my area.
Was very helpful in selecting the part and was very efficient in sending it.

Removed the old broken burner and slid the burner prongs into place. Very EASY to replace!

After finding the correct Y-frame, inches and watts in a surface burner, it was easy to just slide in the slots. Tested, and it was perfect. Now it makes all of the other burners look bad. Thanks. Your site was the only one, that I was sure I had the correct part.

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

pulled out old burner and pushed in new burner.
No tools needed.

extremely easy to replace the burner. I just pulled out the old burner and replaced with new one. The whole process took less than ten minutes.

Simply removed new burner from box and plugged it in! Very pleased with 3 day speedy delivery. Confident my 32 year old cooktop will continue to give many more years of service with any parts needed from PartSelect.