37H-42T-EV ((B1X)) Maytag Range - Instructions

Karen from OLNEY, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both burners were faulty, neither would come on or heat up.

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

Parts Used:

Rex from Keyser, WV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burned up oven door gasket needed replaced.

I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.

Parts Used:

Oven Door Gasket

Daniel from Prescott, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

7 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners weren't heating

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Parts Used:

james from killingworth, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner wouldn't heat (wiring failure)

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

Parts Used:

Eugene from San Antonio, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner would not stay heated had to wiggle the burner to make heat

Replaced with the new burner works like new. Thanks a bunch!

Parts Used:

Marjorie from Swanton, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electric Stove Burner was working unreliably

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

Parts Used:

Jacqueline from Austin, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inside was missing

Great I can bake now

Parts Used:

Thermostat Knob

maria from MANTECA, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burners wasn"t getting hot like they should

i just unpluged the old burner and slideed the new burners in place and they work great now like a new range

Parts Used:

glenn from ST AUGUSTINE, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner plugs were loose

used the supplied parts...very easy. The parts were exact replacements.

Parts Used:

James from CONCORD, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners needed replacing

Pulled out the old burners and put in the new ones.

Parts Used:

Alene from INDIANAPOLIS, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner receptacle failed (stove over 30 years old)

Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.

Parts Used:

BETH from COUNCE, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The larger burners would stop working while in use.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

Parts Used:

Lisa from PORT JEFF STA, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Element did not heat

Pulled out element, plugged in new element. About 5 seconds.

Parts Used:

Mary from CHARLESTOWN, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Jennair cooktop with coils lost one of its coil guides.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

Parts Used: