All Installation Instructions for Kenmore Refrigerator 25373211013

Freezer Freezing up and blocking the vent for refrigerator, not cooling the fridge.

Went pretty straight forward, except the heat shrink tubing was about 2 sizes too big. Would not shrink small enough to seal the connections. Even with a heat gun it would not shrink small enough. OH, another think is when I plugged the fridge back in the defrost timer was in defrost mode. Took me a few minutes to figure that out and use a screwdriver to turn the timer back to the on position. Other than that, install was pretty simple.

Parts Used:

Defrost Thermostat

Defrost Timer - 120V 60Hz

Dennis from BEAUMONT, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

16 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Motor had failed due to ice ejector frozen to tray.

Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.

Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).

Parts Used:

MOTOR-ICE MAKER

Christopher from Middletown, CT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the rail broke on the meat drawer holder

I removed the shelf that hold's the rail's then one (1) screw that hold's the rail in place then I replaced the shelf. Simple & Easy!!

Parts Used:

Drawer Support Rail - Right Side

Geronimo from McAllen, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken Refrigerator Door Shelf Retainer Bar

We took off the broken bar and put on the new one. It clips on. Took about 10 seconds and could have been done by a 5 year old.

Parts Used:

Door Shelf Retainer Bar

Ward from Stockton, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

refrigerator door would not fully close

Took old gasket off and put new gasket into place. Part came in the mail in 2 days. Hardest part was finding the model number of the refrigerator.

Parts Used:

Refrigerator Door Gasket

Elizabeth from Chicago, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Leaking Door Gasket

Open door remove old gasket, remove new one out of packaging install new gasket

Parts Used:

Refrigerator Door Gasket

Ulrich from Ontario, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

12 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Leaky Seal

Just snaps in. Pull the old one out push the new one in. It has a groove it fits into no fasteners to undo, Just pull the old one out with steady pressure.

Parts Used:

Freezer Door Gasket - White

Travis from Tecumseh, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken bar and seal

Snapped in the bars and with the seal once on the track went right on

Parts Used:

Door Shelf Retainer Bar

Mark from Sandwich, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Gasket was not holding tight and I replaced with a new one.

Just like you showed on you tube.

Parts Used:

Refrigerator Door Gasket

Kebreab from NASHVILLE, TN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken drawer support and drawer'

Drawer support held in by one screw drawer slide in no problem

Parts Used:

Meat Pan

Drawer Support Rail - Right Side

Cameron from Bronx, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken meat drawer support

Took out the broken piece, replaced it with the new support using only a screwdriver, and VOILA, it was finished. Thanks!

Parts Used:

Drawer Support Rail - Left Side

Sue from Ocala, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker failed

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

Parts Used:

Refrigerator Ice Maker Assembly

Mary from SOUTH LYON, MI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken fan with vacumme cleaner

I remembered to unplug first. took the little cover off on the bottom, unscrewed the 3 screws. then just held the base that the fan is on and pulled rite off, pushed the other one rite on. it took me five min, i want to say thanks to parts select, had the part, fast shipping, great job, thank you.

Parts Used: