1106708622 Kenmore Dryer - Instructions

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

This model top can be popped off after removing the two screws under the lint filter. Once exposed remove the old cables and feed them through the hole on the front panel. Feed the springs through the ends of the cables and hook the other end into the dryer side panel slots towards the top on each side. Once both cables are fed, feed the opposite ends of the cables into the slots in the dryer door (after popping the white plastic covers out of them first). Put the white covers back into the slots to hold cables into doors. The door catch kit install is pretty obvious.

I didn't. Don't know how to get to light bulb to change it for this specific model

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrosting properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!

Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.

Followed the instructions, removed the back cover, disconnected the top, disconnected the element and removed the element holder, then the element. Reversed procedure to install the new part.

Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.

Removed screws by lint trap, used putty knife to pry top of dryer apart, use nut driver for two bolts that hold the front panel of dryer on, replaced parts, put it back together.

Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.

I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Select. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise

Pull out the old lint filter unit; push in the new one.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.