Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
my dryer would not heat up any longer
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!
Our dryer was leaving rust marks on our clothes that looked like a brown pencil mark. It turns out that the rear drum seal in our dryer was absorbing gunk over the years and we had to change it. It was a fairly easy fix but did require pulling the dryer almost completely apart. While we had it apart we changed this as well.
Anyone with a socket stet and screw driver can get it all apart. On our machine, start by removing the 2 screws that hold the lint filter neck to the top of the machine (under the flap). Then pry the top of the machine up in the front. It will pop up and you can fold it back. Then you will need to remove 2 bolts and undo the plug. From there you can pull the front off and get to the drum.Make sure you note how the belt tensioner comes out (under the drum) and how the belt is routed. It's quite basic. After you get the drum off, peel the old seal(s) off and put the new seal(s) on as directed.
The dryer door was broken down, dryer would not come one
I pried up the lid, and removed two screws from the lint trap door. Removed to screws that held top front of dryer. One on each side near top.
Cables replaced easily, popped plastic retainer from door, inserted cable and connect to spring.
Removed two screws that held the door switc on. Replaced with new switch and pushed wire clips onto new switch.
Things went back together just as they came off.
When I pulled the dryer front away, the tumbler (tub?) pulls out and drops down an inch or so. When putthing it back together , I had to life the tub up to fit into front again.
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Washer stopped working mid cycle restarts after resetting lid
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Took off the lower front panel, removed duct piece from filter to blower fan, removed two screws and two wires to thermostat in exhaust ducting, then replaced thermostat with new one. Very easy job and everything worked like new when I reassembled it.
Do to age and heat the dryer door handle was brittle and broke. Ordering was easy on line. Part was delivered faster tan expected. Oh and the repair time, Less than 1-minute.
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!
We took the screws off of the back, took out the thermal fuse and replaced it with the new one. We watched a video of how to do it which made it so easy. Works great!
The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.