11026934691 Kenmore Washer - Instructions

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

After determining where the leak was coming from I searched the web for help. Your website was the most helpful. I used some of your previous client comments to help me fix my washing machine. After trying without any luck in removing the broken pump I referred to your repair stories and determined that I would need to apply a little more force. Using a screw driver and hammer I pried off the face of the existing pump, then I used pliers to pull out the impeller, after that I was able to remove the remaining piece of the pump. After that I sanded the shaft, applied some vaseline and then installed the new pump. It was very easy once the broken part was removed.

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

1. Removed back panel.
2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor.
3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly.
4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off.
4. From bottom of unit disconnected motor/transmission unit from wash tub.
5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one.
------------------------------------------------------------
Steps 1 thru 3 were unnecessary.
All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points.
Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time.
Forgot to order suspension spring clips, order them next day shipping came the next day .
Just because parts are in stock doesn't mean you will receive in a timely fashion if you need parts better order next day freight.
Videos, parts diagrams and instruction are great, regular freight is not good

I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE DO THE STEP AND REPEAT

After moving washer and UN-Plugging electrical. 1. Remove the 2 screws that hold the Control Panel to the lower chassis. 2. Lift the Control Panel up and forward to expose the water level switch. 3. Remove the dial. 4. Remove the old switch, (a plastic tab locks it into the panel, try to release it(from the front) with a small screwdriver, (mine broke off, releasing the switch). 5. Remove the electrical connection by lifting the connection locking tab. 6. Remove the air tube. 7. BLOW into the air tube to ensure it is not blocked. 8 . Reconnect the air tube and electrical connection. 9. Carefully install the new switch into place, turning it to line up and lock the tab into the panel. 10. Re-install the dial and return the Control Panel screws into the lower chassis. NOTE: If the included air hose needs to be replaced, the time and difficulty needed to make repairs will increase.

Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.

Tipped the washer (combined, stacked washer and drier)back against the wall at a 45 degree angle and braced it up for safety. The pump is located at the front and bottom of the washer. Access is cramped. Removed the spring hose clamps with pliers, disconnected the hoses and released the metal pump attachment springs. Pump came off the drive shaft with a good pull. Reinstalling was more trouble due to the cramped access. The shaft needed to be sanded and lubricated with silicone before the new pump would slide on. It required a fair amount of force to get the pump in position, reconnect the hoses and the clips holding the pump. The top clip was the most difficult. Repair successful.

Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.

Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!