11016922503 Kenmore Washer - Instructions

pulled lid off[fabric softner already removed], removed 7/16 bolt, pulled up, removed dogs, replaced with new, reassembled,and WIFE HAPPY!!!

Found a video showing repair steps on YouTube. Removed agitator cap, seal and retaining nut. Replaced old cogs and reassembled.

Pull top cap off, removed inner disk, used 7/16 socket to remove bolt and replaced cogs. Thanks for instructions online. Ken

Just follow the partselect video connected to the part! I have tracked down some appliance parts locally in the past but I must say that using partselect was so much easier and educational than driving across town and/or making calls. For $10, the 10yr old washer is back and operational as it should be. It's only about a 15 minute job but after reading other comments here, I went ahead and cleaned the scum(yes you have it too) on the inside of both the bottom and top agitator pieces. If I need appliance parts, I will be back to partselect. Ordered Sun at 930p and got part Tue at 10a. Great Job! Great Service! Good to see it still exists out there.

Follow your repair video, excellent.

Super easy repair for my 20 year old washer. I have a really small laundry room and was worried about how much of an ordeal this would be. I had just enough room to remove the housing and get to the motor assembly without putting the machine on its side. The repair was just as shown in the video; 2 clips for the pump, 2 screws and 2 more clips to separate the motor from the transmission. I installed the new coupling and was doing a load of clothes in less than 30 minutes. Great service, fast delivery and low price. I will be coming back to PartSelect for my next repair.

After watching the video the repair looked easy. I took apart the unit per the video instruction, ordered the part and had the washing machine back up and running in 48 hours. Easy and the wife is happy!

watched video on facebook, and followed the instructions,one of the easies repairs I have had to do in a long time.

removed the aggitater and the replaced coggs, no difficulties at all ,thanx for the very quick parts delivery

Being 77 years old an use a wheel chair it took longer than when I was younger but even so it all went well. I removed top control panel, unplug wire connectors, pulled case away so I could lay machine back, remove pump retainers, motor retainer bolts then retainers. then pried coupling apart and installed new one which is better made with metal insert so I had to drive it on, the new switch was an unplug connector and ground screw simple thing then put case back on, snap clips in place, hook connectors up & screwed controls down. Thanks

Flipped the machine on its front, noticed a pile of black rubber dust, identified where the dust was from. Took some time moving pieces around to get access to the coupling. Finally got it off and saw that 4 of the 6 plastic pins that hold the rubber piece had snapped off. Ordered the part and waited a couple of days (the site said 5-8 days or something but it only took 2). Wife got tired of broken washer spread all over the place but I didn't want to move it until I got the part. It was more challenging to get the part in than it was to take it apart because there's not much room to get your hand where it needs to be. I ended up flipping the machine a few times until I got it where gravity was pulling the motor down, giving me enough access to put the part in. My biggest fear was that the hoses weren't tight enough and that I'd have to take it out again, but it was fine and everything's worked great since.

followed repair instruction,( bought on line and down loaded ) some instructions were unclear but when you have the machine apart its obvious. your parts breakdown helped more than the instructions once the cabinet was opened.

I watched your'e easy to do repair video and it was so easy. I just followed the instructions and it saved me an expensive service call as we live in a rural area. Thank you so much.

The lid switched arrived as indicated by the order information. Pulling the washer out to remove the rear panel was the most difficult part of the repair. 5 screws had to be removed before changing out the switch and installing the new part. The repair proved successful after the washer filled with water and began agitating on its own.

I unhooked the two motor brackets, dropped the motor down out of the way, separated the coupling into three parts and slid them in place one at a time. I had to tap them a little with the hammer to get them on the shaft. I put the motor back in place and was done. It worked great and took about 20 minutes.