Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Icemaker Quit Making Ice
Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very from. It makine s the reconnection differcult.
removed two screws holding the control box to the top inside , removed three wires from the thermostat, removed the thermostat from it's mount . It just snaps in or out. removed the thermal weight from it's holder. Again, it just snaps in or out. Reverse the process to install the new one.
Ice maker stopped working after less than six months
After checking all connections I determined the ice maker which had been replaced on 01/2007 stopped making ice. I had serviceman from a local company return and check the ice maker. He rinsed the ice maker under warm water, melting the ice build-up and re-installed the ice maker. I watched him do the re-installation, then waited for two days to see if the ice maker was functioning. Since the ice maker wasn't working, I called the serviceman, who in turn informed me that the replacement ice maker had increased in price from $170.00 to $274.00. That is when I contacted your web site, ordered the replacement ice maker. I was totally amazed and pleased by the fast, easy, and efficient way my order was processed and the ice maker was delivered. I followed the instructions included with the ice maker, and installed the replacement ice maker in about 20 minutes. I can't thank you enough for the great service. I only wish I had checked my computer after the first ice maker broke down and found your web site.
The wiring harness was a straightfoward plug in replacement after depressing the securing tabs, and did provide power to the icemaker. However, the icemaker would continually cycle, with the mold heater on at all times. I suspect this is what caused the thermal fuse to blow in the first place. Rather than spend more time replacing individual components, I eneded up replacing the full ice maker assy. The new ice maker works properly.
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
We looked and looked for bins for the door for more storage. No place had them! Then we found parts select online and there they were. They were so easy to find with the way the website is set up. Its fool proof shopping! The order was placed on monday and we had the bins wednesday morning, the shipping was so fast! All i did was open the box and wipe them down and snapped them in place. Now we have so much more storage by adding all 3 door bins! Thank you So much Parts Select, you R O C K!
We have a side-by-side and the tutorial was different than what we have. Had trouble getting cover off, but finally repaired and WE HAVE ICE! Also took longer than expected. Saved a lot!
Easy removal. Easy Plug and play install. Didn't even have to use the other wires. After install, put 4 oz of water into ice maker and wait....it didn't start making ice right away, but a couple hours later I heard the wonderful "ice dropping into the bin" sound. Worked great ever since.
1.removed 3 nut screws-2 on top &1 on bottom. 2.unplug ref. from outlet. 3.unplug the wires from ice maker to ref. 4.remove ice maker 5.rinse new ice maker 6.plug ice maker to ref. using included wires 7.screw 2 top nut screws first then the bottom. 8.plug ref. back to outlet 9.made first ice in about 2-3 hours
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Bulb wouldn't light up, when freezer drawer was pulled open
The repair didn't get done, because both times that I requested a 25-Watt Light Bulb, I received a 3.6 Watt bulb instead & neither one worked. So I tried testing the original bulb in a table lamp & it worked. So I sense that the problem may be in the switch that allows the light to turn on when the drawer is opened & shut off when the drawer is closed.
Refrigerator would not cool down. Evaporator fan inop.
Unplug, then remove shelving and rear panel. Remove fan motor, swap wired and install new motor. Reinstall in reverse order. Plug back in and verify the fan is running. Easy and nothing special. Only thing I would caution is they use a foam runner to the refrigerator that may be iced up. Carefully clean the ice out before reinstalling everything. A follow up note. If the fan has not been running, Ice will build up in the drain tube. When you start up the refrigerator, you will see water dripping into the lower shelf. This is easy to fix. Unplug refrigerator and disassemble to where you can see the coils. There will be ice on the bottom covering the drain line hole. You will need to carefully chip away the ice, then use a hair dryer to melt the ice. Carefully use a pointed tool to push in the drain tube until the water drains. Go slow and be patient. Heat is your friend when doing this.
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
