10648267891 Kenmore Refrigerator - Instructions

Pulled out old drawer. Slid in new drawer. Super easy!

Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

pulled door off like video showed and undid the small bolts holding cams on and put new on. It was real easy. Thanks for youtube video

Removed the back lower cover, behind the fridge. Uncliped the wiring. Removed the motor, (3 Screws).I did check the new motor before removal of the old one, to verify the older motor was the problem. After removal of the fan & motor. Removed the fan and placed it on the new motor, three screws later, plugged up the wiring, (I didn't changout the wiring, and the Refrigerator is good as new.

First I removed the top bracket cover screw with a 5/16" nut driver. placing it aside, I removed the three screws holding the top door hinge off using a 5/16" socket on a 1/4 drive to free the screws , then continued to remove them with the nut driver. placing them aside on top of the refrigerator. Then I lifted the door up and off the lower hinge and laid the door down on my kitchen counter. I removed the lower hinge piece from the lower bracket still on the fridge with a 5/16" nut driver and installed the new piece in its place and also applied a few dots of Vaseline on the lower hinge piece, I then removed the screw and lower bracket from the door and installed the new one and also applied some Vaseline on this piece also. I also took a rag that had been dipped in olive oil and rubbed the entire gasket surround the door to lubricate the gasket to keep it soft, then I reinstalled the door back onto its lower bracket, and then lined door back up correctly and reinstalled the top mounting bracket and screws then the cover, and then tested door. Door opens now with no noise and opens easier also.

Watched your video pull the door off switched parts and all done . Thanks to your web site it helped me diagnose and fix the problem

Just like the video I watched online at your web site. piece of cake.!!

If you have to push your door to close it and it doesn't close on its own, this is your fix. These door cams are two plastic pieces on the bottom hinge, one on the door and one on the bracket that goes to the body, that engage like a gear with only a couple of teeth. They are supposed to have raised teeth that engage to ride the door to a closed position when it is nearly closed. They are plastic and are made to wear down. To change, empty the door, then at the top of the door (i.e., looking down from above) unscrew two bolts that go to the hinge. The door then lifts off the bottom bracket. Put the door on a soft surface and unscrew the bolt that holds this cam. You can re-use the bolt. There is another cam bolted to the bracket that stays attached to the fridge. Change both cams at the same time. Reverse the process to re-install the door. Your door will close like new for under $10, in maybe 15-30 minutes.

Upon arrival I unpacked drawers and set in their location

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Technically, the repair did not require specialized knowledge. However, replacement of the motor required some effort. Because the motor is located at the bottom of the unit in an area with copper tubing & wiring hindering access it was physically difficult to remove and then replace the motor. A problem arose because the shaft on the replacement motor was larger than the original motor's. Thus the fan would not fit on the new motor. Luckily, I found a fan locally that fit the motor. It would be very helpful if a fan was included in the motor kit. The ref. is now running smoothly

Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

Removed the cover from Thermostate, removed the wires, and screws holding old thermostate, reversed instulation with the new thermostat, pretty simple.

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

Viewed the viedo - it showed what to do