10644269600 Kenmore Refrigerator - Instructions

Removed broken drawer and inserted replacement.
The first replacement door I received was itself broken. A replacement was promptly sent.

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

adjusted other shelves up and down as needed, Made necessary room, popped in the new shelf.

The part arrived within two days of ordering. This was the fastest on-line delivery I've ever experienced. Outstanding service!

I installed a Ice Door Kit. It works Great Now!

removed old parts checked connections replaced parts did not fix problem

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Unplugged the bad one and plugged in the good one.

Prior replacement quotes hovered around $85 plus S/H, so I had given up on it until I found this site through BargainBabe.com. The first bin shipped was cracked; I received a full CC credit the same day I reordered. Second bin arrived in good shape. The humidity adjustment piece is a bit loose, but we don't move it around once we set it anyways. All good and quick at about half the price.

Replaced with the new one

The new drawer I ordered from PartSelect fit perfect and is identical to the drawer that broke.

I ordered this item on a Tuesday and received it on a Thursday. I was AMAZED!! Thanks for making this huge annoyance in my life so easy to fix. I will use this site every time I have a part that breaks for any appliance and I'd recommend this site to anyone!!!

Took the old out and replaced it wit a new one

pulled all shelves from refrigerator door. unscrew the top plate and lift door out of bottom. pulled old cams off the door and the lower bracket and installed the new cams. put door back on and screwed the top bracket back on. installed the door shelves back in the door. never took the food off the door shelves. easy, easy, easy.