10644022603 Kenmore Refrigerator - Instructions

To get me thinking. . . Our thermostate was not working. . . It was under warrant. . Call repairman. . He came out. . Looked at it, went to supplier got a new one . . . Unplugged old thermostate and plugged in new one. . . . Charge. . . $120. 00 So when the ice maker went out I checked and it was out of warranty. . . Took off door to unit. . 2 Screws. . . Unplugged unit. . . . Ice maked is on a shelf that has notches. . . Lift up a little and slide out. . . Ordered new uniy from partselect. Attanched to shelf. . . Plugged in to electricy and installed shelf. . Prayed a lot and works . . . . Al wilson

The first maker I received was broken. The funnel at the top that directs the water into the tray was broken. I called PartSelect and told them how I had received the part and there was no problem. They shipped me a new part, and it must have been the same day as I got the replacement two days later. I was very satisfied with that quick response. I removed one screw and the cover to the wiring harness. Slid the icemaker forward and unplugged the wiring. Then removed the icemaker. I had to remove the old bracket from the assembly as the new maker did not come with one. Installed three screws in bottom of bracket then reinstalled the assembly and plugged the wiring back in. The whole process took about 10 to 12 minutes, very easy.

Ordered a replacement which arrived quickly, and delivered the next day. It was not difficult, three screws to undo and one electrical connection.

A snap! The part arrived the day after I ordered it. (How, I don't know). The video showed exactly what to do. I did it. Ice maker now works like a charm. Thanks.

I removed the ice maker, saw the problem, took the ice maker apart and ordered a new mold. I reassembled it with the new mold and it now makes ice but the control arm remains up after each ice dump. I plan to take the ice maker back out when we leave (we are snow birds in Florida) and see if the arm is properly placed.

Replaced the emitter/receiver and it worked after that. Very easy.

Removed screws holding face plates in place inside the freezer housing ... unplugged the old emitter and receiver, then plugged in the new emitter and receiver. Screwed the face plates back in place. Actually, this repair took place a few years ago. When my ice maker quit recently, I noticed the red light inside the freezer housing was not blinking properly. I remembered from my previous experience that the pattern of red light blinks was diagnostic, but of course, the pattern is not described in my owner's manual. The installation instruction sheet that comes with this part does give the diagnostic patterns, however. As it turned out this time, when I was ready to install the new parts, I discovered that one of the little ice-flipper thingies (technical term) was caught on the ice cube-freezing tray ... I released the flipper thingy, and, in time I was back in the ice-making business. So the new part is stowed away in the pantry until the present emitter/receiver parts fail ... and I made a copy of the red-light diagnostic pattern to put in the owner's manual. Now, all I will have to do when the existing parts fail, is remember where I stowed the replacement parts!

Pulled the old one out and replaced it with a new one.
Very Simple.

I tried several things first : changed the filter cartridge, then the water control valve, then the control boards but still no ice. Rather than buy a new motor assembly, I bought a whole new icemaker which included the motor assembly and finally SUCCESS! In total it cost me about $350 but you have to try the easier and cheaper things first. One 1/4" screw and disconnecting the wire harness clip plus reusing the old icemaker base and the repair was complete. I would recommend a more detailed discussion on what each part does and the way the colored wires attach. Wire clips can sometimes be connected upside down. I was very happy with how quickly I received the new part. I whole-heartedly recommend PartSelect.

the ice maker is held in by on screw. then whole unit comes out.three more 1/4 inch screws hold main unit in.put unit back in was makeing ice in under 30 min.
i ordered part wed night recieved it on fri. highly reccomend parts direct.
oh yeah my 14 year old son did the repair because i was out of town.

Removed icemaker found ice mold protective layer coming off. Replaced ice mold and working great. Online graphic very detailed and easy to determine part needed. Easy and great delivery. Highly recommended for future repairs.

Removed old unit and installed new unit. It was quick and easy.

replaced icemaker

After troubleshooting to determine that I needed the Icemaker assembly, I ordered the parts early on a tuesday and they arrived the next day. Quick. Opened the box and there was no packing material, just the icemaker in the box with a slip of paper instructions with one sentence on it. Said to remove ice shield from old icemaker and install on new one. To remove the old icemaker, I first had to removing the one screw on the bottom that secured the cover over the wiring harness. Next I removed the cover by sliding it towards back of freezer section and guiding around wires. Next I depressed up on two spring clips on the bottom of the icemaker to release it from the tracks and slide the icemaker out. Be careful with the hose for the water outlet. You may have to tip it backwards to get it to clear. Once out of the tracks, I disconnected the wiring harness and removed old icemaker. I reversed the process to stall the new one after I had removed the three screws and the ice shield off the old icemaker and installed on the new one. After installation, it took about 10 minutes for the sound of water running into the trays and we had ice 30 minutes later. Worked fine and hasn't missed a beat yet.

Took out 5 screws and replaced the unit easy as can be.