Tappan Freezer Seals and Gaskets

Your Price

$143.35

Tappan Freezer Refrigerator Door Gasket

★★★★★

13 Reviews

PartSelect Number PS11770644

Manufacturer Part Number 5304507200

This door gasket, also known as a door seal, is sourced from the original equipment manufacturer for use in refrigerators and freezers. It is a flexible rubber strip that runs along the edge of the appliance door. It creates an airtight seal between the door and cabinet to prevent cold air from escaping, and warm air from entering the refrigerator, to ensure that the temperature in the appliance remains constant. Over time, the door gasket can lose its elasticity or tear. In this case, you will likely notice frost build-up, increased noise, and inconsistent temperatures. Peel the faulty gasket off the refrigerator frame and remove any debris or residue on the surface. Carefully place the new seal along the edge of the door and press it firmly into place. Secure it with the appropriate fasteners and close the door to verify that there are no gaps between the door and cabinet.

Fixes these symptoms

Door Sweating
Frost buildup
Leaking
See more...

Installation Instructions

Louise from Ocala, FL

Ice and frost were forming in a frost free freezer

The old gasket was obviously gapping, partially from age and partially from damage during a move. To make the repair, I loosened the screws that are under the gasket and hold it in, but did not remove them. Once all were loose, I removed the old gasket, then starting at the top, ran a thin bead of food grade RTV under the portion of the door that captures the gasket. I put the sealant on that edge only, then carefully worked one of the short edges of the gasket under the plastic and tightened all but the corner screws. I then ran the RTV down the inside of the hinge side of the door and repeated the process, this time tightening the top screw and the hinge side screw at the top, but leaving the bottom most screw loose. I repeated the process on the opening side of the door. The bottom was the hardest because the gasket seemed just a little long and it was hard to get the RTV up and behind the door portion, but after a couple tried I got a good bead of sealant then slid the gasket under the door capture and tightened all the remaining screws. After closing the door, it was obvious that there were places were it did not seal well. I used some cardboard strips, cut from the box the gasket came in, to place inside the freezer, between the hard plastic of the door and the inside of the gasket where it laps over the screws. This helped a lot, but there were still a couple small areas, so I used more cardboard, from the outside, between the main portion of the gasket and the rim of the gasket. This eliminated all the gaps. I let this sit overnight and this morning removed all the cardboard for a great sealing freezer. Read more...

Your Price

$252.35

Tappan Freezer Door Gasket

★★★★★

4 Reviews

PartSelect Number PS447460

Manufacturer Part Number 3206261

This gasket is intended for use with upright freezers. This white door gasket is used to make an air-tight seal for the cabinet when the door is closed

Fixes these symptoms

Frost buildup
See more...

Installation Instructions

Sharon from Green Valley Lake, CA

The freezer was going into alarm

We loosened all the screws around the door and slid out the old gasket.
We then slid the new gasket behind the panel and screwed the screws back in place. Read more...

Your Price

$170.25

Tappan Freezer GASKET-DOOR

PartSelect Number PS2378625

Manufacturer Part Number 216481211

Fixes these symptoms

Frost buildup
See more...

Installation Instructions

Arnold from Quincy, IL

Door gasket needed to be replaced.

I removed all of the expandable pins that held the gasket and the inner door panel, and removed the old gasket from the inner door panel. The new gasket was then placed around the edges of the inner panel. While holding the gasket and panel in the proper location, the expandable pins were inserted into the mounting holes, finishing the installation. Read more...

Your Price

$172.45

Tappan Freezer Door Gasket - White

PartSelect Number PS2378626

Manufacturer Part Number 216481411

Fixes these symptoms

Frost buildup
See more...

Your Price

$44.05

Tappan Freezer Door Secondary Gasket

★★★★★

1 Review

PartSelect Number PS2361201

Manufacturer Part Number 216524201

Fixes these symptoms

Frost buildup
See more...

Your Price

$153.58

Tappan Freezer Gasket

★★★★★

2 Reviews

PartSelect Number PS425944

Manufacturer Part Number 216481001

Your Price

$165.72

Tappan Freezer Lid Gasket

PartSelect Number PS425946

Manufacturer Part Number 216481101

Fixes these symptoms

Frost buildup
See more...

Your Price

$175.69

Tappan Freezer Door Gasket

PartSelect Number PS447455

Manufacturer Part Number 3206256

This white door gasket is used to make an air-tight seal for the cabinet when the door is closed.

Fixes these symptoms

Frost buildup
See more...

Installation Instructions

James H from KNOXVILLE, TN

Ice crystals formed near gasket.

Removed the freezer door which had an electrical cord routed through the lower hinge with a disconnect under the freezer. Job works better with two people. Working the gasket into place was a little tricky at the corners. The putty knife was helpful. Make sure door is not warped when replaced on freezer. If warped slightly the door can be twisted to make gasket fit evenly bottom to top on front edge. Hope this helps DIY folks. Read more...

Your Price

$150.75

Tappan Freezer Door Gasket

★★★★★

2 Reviews

PartSelect Number PS425939

Manufacturer Part Number 216480801

This white door gasket is used to seal the freezer door when closed.

Fixes these symptoms

Frost buildup
See more...

Installation Instructions

Patricia from AMERICAN CYN, CA

The freezer door gasket needed to be replaced.

When I received the new gasket I took a blow dryer to it and straightened out the warped areas prior to removing the old gasket. I then looked for a tool to remove the pins holding the gasket in place. I found a butter knife worked the best to get underneath and pry them out. Since this is a chest freezer, the pins in the back of the door were very hard to remove and one of them even broke off as I was removing it. Of course I had no spare pins when I went to put the new gasket in place. The new gasket slid right on and the pins snapped into place with a little bit of HARD pressure. My advice is to make sure that you do the back of the door first, since it is hard to line up the holes and the pins otherwise. It would not have been a difficult repair if not for the pins giving me trouble. There are no instructions sent showing how to do any of this work, so if you are not knowledgeable about gaskets this repair could be a difficult one. Maybe the company could include some basic instructions as a help to their customers. Read more...