Quick Question!

Have you ever purchased from PartSelect.com before?

774514-1-S-Whirlpool-8193762           -Fuse Kit
774514-1-S-Whirlpool-8193762           -Fuse Kit 774514-2-S-Whirlpool-8193762           -Fuse Kit 774514-3-S-Whirlpool-8193762           -Fuse Kit https://www.partselect.com/Schematics/Whirlpool/4LU620JN.gif

Fuse Kit

Your Price

$16.56
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS774514
Manufacturer Part Number 8193762
Manufactured by Whirlpool

When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.

This part works with the following brands: Kenmore, KitchenAid, Whirlpool, Inglis, Estate, Roper.

This part works with the following products: Dishwasher.

This part fixes the following symptoms:

  • Will Not Start.
  • Not draining.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

Clean light blinks 7 times. All lights work but will not let dishwasher start. Cancel button engages pump/drain sound but after cancel cycle ends, clean light comes on and begins blinking again.

Suzanne for model number DU1100XTPQ6
Answer:

Hi Suzanne, Thank you for the great question, when the clean light blinks 7 times this means that your dishwasher is failing to heat the water in an allotted time. There are a few reasons the light is blinking, but the first thing you can try is to reset the control board. Press high temp wash, heated dry, High temp wash, heated dry, high temp wash, heated dry, high temp wash, heated dry, high temp wash. If you don’t have a “heated dry” button, use the “air dry” or “energy saver dry” button. All the lights will light up, then press cancel to reset the board. If the control board doesn’t reset, you may have a faulty control board and the control board will need to be replaced. If the board resets you can start a new cycle and see what happens. If the the clean light blinks you can to reset the board again, some times it takes 2 or 3 tries. The most common reason for this blinking is because the water coming from your household water supply is too cold. The dishwasher is expecting 110 degree water to enter your dishwasher.You can try to run your faucet next to the dishwasher until the water coming out is hot. Also make sure the dishwasher is has a good water pressure. Put a mug or similar sized glass in the upper rack facing upwards and run a cycle, It should fill witin10 minutes of starting the cycle. If it doesn’t fill with water then the dishwasher isn’t producing enough pressure, this will cause the water not heat properly. You can try to take your pump and motor assembly apart to clean inside to see if this helps with pressure. You could also have a faulty heater, control board, or high limit thermostat. You need to uninstall your dishwasher, disconnect power and lay it on it’s back. With a multi meter you can check resistance of the heater as well as the resistance of the high limit thermostat. You should get a reading of between 5 and 30 ohms on the heater if it’s good and less than one ohm on the high limit thermostat. If both of those devices che

4 people found this helpful.

Most Recent

Question:

Dishwasher has power to it but doesn't work. Normal wash button illuminates. Cancel/drain button light turns on and off. No other lights, when pressed, work.

Lawrence for model number 665.16012401
Answer:

Hi Lawrence, Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the fuse, the heating element, the door switch, the circulation pump and motor, the high limit thermostat, the electronic control board, the door latch, the capacitor, the door actuator, the chopper assembly and the water inlet valve. I hope this helps. Thank you and have a great day!

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 45 reviews What's this?
 

4 of 6 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: zipora from HOLLYWOOD HILLS, FL

The dishwasher did not start

Open the panel put the wires and plug it in.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 7 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Mary Sue from Massena, IA

Dishwasher didn't finish cycle and water did not drain. Nothing would work when we got up in the morning.

we removed the six screws behind the control panel on the door. Found the fuse on the right side of the door, (thanks to your drawing )and replaced it.. Dishwasher works great now. Your site is great, it is easy to use, shipping was very fast. We will have no problem using your site on all our part needs.
Thanks for your help. Bob and Sue Holste

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Richard from PLANO, TX

Fuse was brunt out

I googled to find the problem and discovered this is a ongoing problem with Whirlpool appliances. I followed instructions provided with the new part, very easy repair

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: john from INDEPENDENCE, MO

Dead would not run

Open door remove screws that hold the black face panel on.Located two black wires that plug on a white square part by the electronic board.Make sure power is off unplug both plugs Pull White block that they plug into comes sliding right off. Slide new one on making sure grooves fit guides. Plug wires on. Turn power on check for lights on front panel reinstall panel and wash dishes. Easy on tightening screws they will strip if you have a heavy hand.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: Walter from HUFFMAN, TX

Green clean light was blinking seven times, would not start or wash

I noticed a burnt smell. I watched the video on how to diagnose and repair the problem, The control panel had a burnt spot on it , I tested the fuse, which was OK. Video showed how to properly test fuse and replace control panel. I breezed through it like a pro ! And I hate electrical stuff ! Unplug unit first, and take your time. Although the control board was $255.00 plus shipping, We did get a $60.00 rebate on old one. We decided that the dishwasher cost to replace, was a lot higher than to repair the machine. We now still have a washer that is of high caliber. Thank you for the great video and the fast service. Have used this site before and will do so for any needed parts in the future !!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: john from JENISON, MI

Dishwasher has no response from front panel

Found out the thermal fuse was the culprit with an ohmmeter. Ordered the part from PartSelect and installed it and the harness kit. Took about 15 minutes and now the dishwasher is running again. Easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: bill from WESTCLIFFE, CO

Quit in mid way though wash

checked for power at fuse and it was ok. used ohm meter and cheked fuse for continuity and found open replaced with fuse kit and is working ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 22 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: CAROLYN from FOLSOM, LA

Not working - clean light flashing

I replaced the heating element. It did not fix the problem. Called a repair man

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Frank from Commack, NY

Dishwasher would not finish cycle. Left water in unit.

Removed front panel of the door. Gained access to the circuit board. Found the fuse and removed it. Installed new fuse along with the new wire harness according to the directions that came with it and everything seems to be working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Ryan from Carmel, NY

Dishwasher stopped working - no power

My repair required the use of basic tools to replace the fuse kit and wire harness. The directions that come the part are very simple, clear, and SHORT. If you follow them you won't have a problem with the repair. It's worth the 30-60 minutes of your time to save repair man costs.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers
Customer: Robert from Augusta, GA

Unit shut down

Trouble shot problem with multi meter.Removed inside top cover of control panel. Unplugged main board then fuse kit - removed - ordered part - replaced(turned off breaker to washer).

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Christopher from Slidell, LA

No power

Turn off circuit breaker. Remove the torx screws that hold the door panel on. There are 8. Remove the door. Open the electronics area. Pull the leads off the old one, pull the old fuse out, attach the wires.

Do no follow the instructions with the part that has you splice in the wires with the part, simply attach the wires that exist to the new part (either wire to either side).

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Richard from Stow, MA

Dishwasher was dead. No lights would turn on.

I removed the screws around the perimeter and checked the fuse for continuity. when it proved faulty I ordered the replacement. I simply cut the wires to the fuse attached the new wires with the connector provided and reassembled. worked like a charm.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Fuse Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Misty from La porte, TX

Washer quit mid cycle, full of water, no power to control panel

opened control panel, snipped 2 wires, stripped them, inserted new fuse and harness, closed it up, all after turning the power off at the breaker ofcourse

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Charles from Exeter, NH

Thermo cutoff switch failed

Removed front cover, ~12 screws, which exposed the wiring harness and associated circuit boards. Per instruction supplied with new thermo switch, removed and replaced switch.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS774514
Manufacturer Part Number: 8193762
Brand Model Number Description
Kenmore665110739120Dishwasher
Kenmore665110739130Dishwasher
Kenmore665110739140Dishwasher
Kenmore665110739190Dishwasher
Kenmore66514353300Dishwasher
Kenmore66514353301Dishwasher
Kenmore66515872000Dishwasher
Kenmore66515874000Dishwasher
Kenmore66515879000Dishwasher
Kenmore66515882000Dishwasher
Kenmore66515884000Dishwasher
Kenmore66515887000Dishwasher
Kenmore66515889000Dishwasher
Kenmore66515892100Dishwasher
Kenmore66515894100Dishwasher
Kenmore66515899100Dishwasher
Kenmore66515912000Dishwasher
Kenmore66515912001Dishwasher
Kenmore66515914000Dishwasher
Kenmore66515914001Dishwasher
Kenmore66515919000Dishwasher
Kenmore66515919001Dishwasher
Kenmore66515922000Dishwasher
Kenmore66515922001Dishwasher
Kenmore66515923000Dishwasher
Kenmore66515923001Dishwasher
Kenmore66515924000Dishwasher
Kenmore66515924001Dishwasher
Kenmore66515929000Dishwasher
Kenmore66515929001Dishwasher