Rear Drum Seal with Adhesive 239087 | Official Whirlpool Part | Fast Shipping | PartSelect
Rear Drum Seal with Adhesive – Part Number: 239087
( Grid squares measure 1x1 inch )
Rear Drum Seal with Adhesive – Part Number: 239087 Rear Drum Seal with Adhesive – Part Number: 239087 Rear Drum Seal with Adhesive – Part Number: 239087 https://partselectcom.azureedge.net/Schematics/Maytag/P4HELZQV.gif

Rear Drum Seal with Adhesive

PartSelect Number PS333333

Manufacturer Part Number 239087

Manufactured by Whirlpool

Product Description

Rear Drum Seal with Adhesive Specifications

Includes high temperature adhesive.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Noisy | Marks left on clothes | Takes too long to dry | Will not tumble

This part works with the following products:

Dryer.

This part works with the following brands:

Kenmore, Whirlpool, Roper, Estate, KitchenAid, Crosley, Inglis, Admiral, Magic Chef, Amana, Maytag.

Part # 239087 replaces these:

239087, 239087VP, 3290, 337449, 337499, 4319323, 8066085, AP3093452.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Kenmore Dryer Rear Drum Seal with Adhesive

Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 8 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lauren from Mckinney, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Parts Used:
341241, 239087
The dryer was leaving rust marks on our clothes.
After my husband disassembled the cabinet and removed the drum, we used a putty knife to remove the old seal and carefully glued the new one in place. (A 2 man job to do it without leaking glue everywhere.) We then replaced the belt, following the picture sent by PartSelect and put everything back. (We put all small pieces in labeled envelopes so that putting it back together was easy.) Another helpful hint - take a few digital pictures beforehand in the event that you need to see it to put it back together!
35 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Jimmie from Lucerne Valley, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Parts Used:
349241T, 239087
squeaky and very loud noise
first we printed out directions from a couple of online repair sites that had pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive replacing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Howard from Tyler, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
239087
Dryer was leaving scorch marks on clothing
UNPLUG THE DRYER!!!!!
First removed the two screws holding the lint filter in place. Then slipped a screw driver between the top and the dryer body to remove the top. Using a nut driver removed the two screws holding the front of the dryer in place, remove the two wires for the door switch., lift the front cover of the dryer and set it aside. Support the drum ( two extra hands would be nice) and remove the drive belt. Then remove the drum. A thorough cleaning to remove all of the scorch like stain from the drum and back plate. Remove the seal and glue the new one in its place. Put it back like you found it. Make sure that the seal is not tucked against the back plate. Dryer works better than new and no more stains.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Christine from Minot, ND
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Socket set, Wrench set
Parts Used:
341241, 239087
It was having a hard time starting and would quit.
First I had to take the top of the dryer off by taking the two screws off of the lint trap on top then I pushed the top forward a little and lifted up. Then I had to take the front of the dryer off (I think there was two screws). After that I had to take the belt off to be able to get the drum out. I pulled off the old seal and had to use some glue remover to get the old glue off. I then put the new seal on did a little bit at a time to make sure it was on correctly. The glue is really sticky once it starts to dry. It takes two people to put the seal on especially when it gets down to the end. Although my dryer defenitly needed a new seal it was not the problem. It was not very difficult at all, just more time consuming with trying to get the old glue off. Will be buying a new motor, found one cheap and alot less expensive than buying a new dryer considering when I am done I will pretty much have a new dryer for about $120.00.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
John from Wilton, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
279827, 239087
Dryer made loud rumbling noise and then shut down
It had been making noise for a week and I bought the two drum support rollers hoping that was the problem. It wasn't as the dryer started shutting down after a few minutes of running. I opened the top of the dryer and removed the 2 screws holding the face and door on. I removed the face and disconnected the door switch wires and released the drum belt by pushing on the idler pully. I then removed the drum straight out the top. I then put a wrench on the fan on the back of the motor and unscrewed it and then released the two holdown clamps on the motor and removed the motor. I had to make a couple of wiring modifications for the new motor but the instructions and connectors that came with the motor were perfect. I put everything back together and plugged the dryer back in and tried to start it and .... Nothing. I forgot to reconnect the door switch wires. Fixed that and the dryer now runs as good as new and makes no noise at all now (almost anyway). It should be good for another 10 years easy.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Sean from BAR NUNN, WY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WP691366, W10854425, 341241, 239087
Belt was slipping, and having a hard time spinning the drum
First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the two side moldings on the control panel and the two screws holding doun the enclosure. Slide the control enclosure forward and lift up . Take a picture of the wiring for later reference and carefully unplug the wires and set the enclosure aside. Next, remove the two screws holding the rear lid retaining clips. Gently pry up on the front of the lid to realese hold doun clips, swing the lid up and remove it from the rear clips, set the lid aside. Remove the two screws on corners of front cover located near the top, unplug the door switch. Remove the front cover by lifting straight up, set aside. Now remove the belt from the motor by realeasing the tensioner and remove it from the drum. You can now remove the drum through the front. Now is a good time to check the condition of your drum rollers, clean them as needed or replace them. Clean the roller shafts and apply a quality grease. "Clean the roller groove on the drum" this is what makes the drum sound bumpy! Remove the rear seal and replace it as per the instructions that come with the seal. The glue dries quickly, so have the seal fully in place and apply glue to small areas replacing the seal fully before moving on. You can now reinstall the drum being careful not to damage the seal. Place the drum on the rollers, reach inside and work the seal into place. You can now replace the belt and work in reverse with the casings! It took me longer to type these instructions than it did to make this repair! Enjoy your like new machine!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Kevin from QUINCY, MA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
4392065, 239087
Belt snapped
Followed the directions, top held in place by plastic clips, used flat bladed screw driver to gently pry upwards until they released. Cleaned inside of dryer. Check for lint, just about none. Two screws retain the front panel. Disconnect the door switch. Installed new rollers, then installed the rear drum seal which can be messy and the hardest part of the whole job. I applied the adhesive to the lip and slipped the seal onto the lip, the adhesive was setting by the time I was done, but it's glued 360 degrees around the periphery. Put belt on drum and slipped drum onto rollers depressed tension and slipped belt onto motor pulley. Slightly pulled drum up while slipping front panel onto lower catches. Reinstalled top clips and retaining screws. Tested. Closed lid. Done. Much quieter and works fine
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Ron from COAL CITY, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
239087
Drum rear seal bad
Took off old one clean surface up then put glue all around drum seal area wait one min. Or tacky then put seal on reassemble the drum. Works good
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
2 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS333333
Manufacturer Part Number: 239087
Brand
Model Number
Description
Kenmore
11060012000
Dryer
Kenmore
11060012001
Dryer
Kenmore
11060012002
Dryer
Kenmore
11060022010
Dryer
Kenmore
11060172000
Dryer
Kenmore
11060172001
Dryer
Kenmore
11060172002
Dryer
Kenmore
11060202990
Dryer
Kenmore
11060212990
Dryer
Kenmore
11060232000
Dryer
Kenmore
11060232001
Dryer
Kenmore
11060232002
Dryer
Kenmore
1106062110
Dryer
Kenmore
1106072011
Dryer - ELECTRIC DRYER
Kenmore
11060882990
Dryer
Kenmore
11060884990
Dryer
Kenmore
11060887990
Dryer
Kenmore
11061252010
Dryer
Kenmore
11061252011
Dryer
Kenmore
11062202100
Dryer
Kenmore
11062202101
Dryer
Kenmore
11062212100
Dryer
Kenmore
11062212101
Dryer
Kenmore
11062512100
Dryer
Kenmore
11062512101
Dryer
Kenmore
11062512102
Dryer
Kenmore
11062514100
Dryer
Kenmore
11062514101
Dryer
Kenmore
11062514102
Dryer
Kenmore
11062872100
Dryer