Part Location Diagram of WB2X2058 GE Door Gasket
See part 534 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Door Gasket WB2X2058

Rated by 4 customers 

Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 132.33
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

Does this part fit my model?

Need help finding your model number?
PartSelect Number PS241985
Manufacturer Part Number WB2X2058
Manufactured by GE for General Electric, Hotpoint
Troubleshooting
This part works with the following products:
Range, Wall Oven.
Part# WB2X2058 replaces these:
AP2010255, 248261, WB02X2058
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.9 / 5.0, 4 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Replace door gasket on very old wall oven
Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others.
1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible.
2. Shut off circuit to oven (optional, but good practice)
3. Remove racks, trays, etc from oven to reduce weight at Step 7
4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers.
5. Remove Phillips screws, one on each side wall of oven liner.
6. Remove two hex screws and metal gasket-holder on top center of oven liner.
7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job.
8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket.
9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner.
10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top.
11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws.
11. Pull out each hinge to broiler position.
12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time
13. Restore power, racks, trays, etc.
  • r from SUNNYVALE, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The gasket needed to be replaced in top oven, it was brittle and broken.
We took out the philips screws on the right and left side of inside of the oven and two hex head screws on the clip on the top of the oven in the front. Then using a slot screw driver pryed the oven liner out enough to remove old gasket and replace the new gasket. We did see in some online directions that we were suppose to remove entire oven from cabinet and loosen bolts in the back. But, we were able to get enough space to get the old gasket out and new one installed. We did use a 1/4" thick piece of wood on face of oven to prevent any denting of oven when prying out the liner of the oven.
  • JoAnn from Auburn, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
19 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket around rim of oven broke while cleaning
Son-in-law unscrewed oven compartment; broken gasket was easy enough to remove and new gasket easy to replace; only problem was oven door would not shut tight. Tried shoving gasket harder into groove, tried turning on oven and heating new gasket to see if it would soften. Finally got it to close by pushing hard on left side of oven and inside light would at least go off and stay off.
  • Dorothy from Santa Rosa, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Gasket Worn and Brittle
Took oven door off. Removed screws that were holding oven insert. Pulled out oven insert. Removed old gasket. Installed new gasket. Push oven insert back. Installed screws. Replaced oven door.
  • Karen from Yakima, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Erc
February 11, 2022
I am in need of a door gasket for a GE wall oven. I found part number PS241985 I want to make sure it is the right gasket. My opening is 46" is this the right gasket?
For model number JKS06G003BG
PartSelect logo
Hi Erc, Thank you for your question. The part number listed under your model number for the oven door gasket is PS241985. If you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS241985
Manufacturer Part Number: WB2X2058
Brand
Model Number
Description
General Electric
10420-1
Range
General Electric
10420-2
Range
General Electric
10421-1
Range
General Electric
10421-2
Range
General Electric
10421-3
Range
General Electric
10431-1
Range
General Electric
10431-2
Range
General Electric
10431-3
Range
General Electric
10441-1
Range
General Electric
10441-2
Range
General Electric
10441-3
Range
General Electric
10451-1
Range
General Electric
10451-2
Range
General Electric
10451-3
Range
General Electric
10460-1
Range
General Electric
10460-2
Range
General Electric
10460-3
Range
General Electric
10461-1
Range
General Electric
10461-2
Range
General Electric
10461-3
Range
General Electric
10470-1
Range
General Electric
10470-2
Range
General Electric
10470-3
Range
General Electric
10471-1
Range
General Electric
10471-2
Range
General Electric
10471-3
Range
General Electric
10477-1
Range
General Electric
10477-2
Range
General Electric
10478-1
Range
General Electric
10478-2
Range
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service