Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Lee H - February 4, 2021
Verified Purchase
Loud and whining noise
The part did come quickly and was easy enough to install. It is much louder than the old one and seems to pulse a little. But bottom line is the ice does dispense!
★★★★★
★★★★★
John M - October 9, 2018
Verified Purchase
Kitchen Aid Ice Maker Auger Motor!
The part works well.
★★★★★
★★★★★
Guy P - August 25, 2018
Verified Purchase
Ice despencer motor
The part worked great! Easy to switch out. Still have issues with the ice distribution which requires another part.
★★★★★
★★★★★
Tim S - May 17, 2018
Verified Purchase
Auger motor
The part I received does not work on my model Ksbs25in bl01. I’m awaiting my refund. Part returned on 8May.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
When pushing on ice dispenser paddle in exterior door, there was no sound from motor or auger.
I had to remove ice storage compartment sitting above motor on door to expose auger gear. Then used a small socket to remove 4 screws from underside of auger motor compartment in door. Motor drops out with a small wiring harness attached. This simply unplugs and then swaps in with new motor. Auger axel was sanded to remove rust and grease
... Read more applied. Motor door and ice compartment were then reattached.
Read less
James from POCATELLO, ID
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser motor wore out
Unplugged power from unit. Removed tray bracket, removed 2 screws from drive motor cover, removed 4 screws from motor assembly, disconnected power from assembly, Replaced rubber seal at the lower end of the recently installed new shaft. Re-connected the power plug, placed the new dispenser assembly into position making sure the shaft was
... Read more properly seated in the motor. Replace the four screws, plugged in main power and tested the dispenser prior to replacing the ice container. Tightened the screws, replace the cover and the tray bracket.
Read less
Larry from AIKEN, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor would not turn
removed cover the four screws that mounted the motor,unplugged and replaced motor
Arnian / from San Diego, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
27 of 47 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rich
August 4, 2017
Ice dispenser motor runs and sounds normal but does not turn blades or dispense ice, i'm assuming something is stripped in motor
For model number KSRP25F
Hi Rich,
Thank you for the question. I would suggest replacing the motor its self as the parts to the motor that turn the blades are not sold separately.
Good luck with this repair!
5 people found this helpful.
Was this helpful?
Thank you for voting!
TOM
December 19, 2019
Pushing the ice dispensing bar produces no motor sound and no ice. Suspect it is the dispensing motor. Correct? If i order a new motor on-line, what is the ease of installation? Or, do i need to call a repair service"?
For model number GC3JHAXTS01
Hello Tom, thank you for your question. Yes, the most likely issue is the dispenser motor. This is a fairly easy repair and shouldn't require a technician. I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Bruce
January 16, 2020
Dispenser motor drive shaft raising and does not spin. Removed cap part 23 and reset the shaft part 26. Works for short period then raises again to become disconnected from the drive motor.
For model number 10658966700
Hi Bruce,
Thank you for your question. Check the end of the shaft that fits into the motor and see if it is worn. If it is worn the shaft should be replaced. If the shaft is fine, you will need to replace the motor. We hope this helps. Thank you and have a great day.
Refrigerator quit cooling overnight. Ice in bucket melted and some water ran down the drive shaft to the dispenser motor. After refrigerator was fixed and cooling again, the motor would not run. Removed motor, thawed out with hair dryer, and left overnight to dry out before reinstalling. Motor worked for 6 weeks but now will not work. I removed the ice bucket to get access to the drive shaft and turned the shaft from the motor. Motor worked for a day or so but stopped again. Repeated turning shaft 2 more times and motor would run for day or so.
For model number KSCS25INSS02
Hi George,
Thank you for your question. Based on the information you provided, the motor will need to be replaced. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mark
July 2, 2019
I need to order part number 26 in this diagram. It appears to be a shaft or rod, part number W10140960.
For model number JS48PPDUDB13
Hi Mark,
Thank you for your question. The part you are looking for is the ice ejector bar. The part number listed under your model number for the bar is PS11740390. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jac
October 25, 2017
Kitchen aid ice maker/ ice grinder has Whirlpool no:2315547 motor..can you replace it as well as the male spline)
For model number KSB525JV5500
Hi Jac, Thank you for the question. Yes the Dispenser Motor is replaceable and comes with the male spades.Good luck with the repair !
1 person found this helpful.
Was this helpful?
Thank you for voting!
Louis
August 4, 2018
I am looking at item number 2315547. It is the ice dispenser motor. When pushing on ice dispenser i hear a soft hum but nothing else. Will replacing the motor solve this issue?
Hello Louis, thank you for your question. Yes, that is most likely the issue if you are not able to get crushed or cubed ice to dispense. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Clair
December 3, 2018
I replaced the ice flapper and now ice motor doesn't run have water it works
For model number ED5JHAXTS00
Hi Clair, thank you for your question. You could double check that you installed the door correctly, we do have a video here: https://youtu.be/2UVP9vBbxGQ. Otherwise you may have to check the wiring to your motor or replace the motor itself. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
