This is a surface burner infinite switch kit for your range or oven. This replacement part activates and deactivates your burner, and controls the burner heat. If you are not getting any heat to your burner or it is not the right temperature, you may need to replace this part. It is about 2.75 inches wide and 1.5 inches tall.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Larry G - January 9, 2021
Verified Purchase
Easy to replace and corrected by problem of the burner no longer working.
Adequate aftermarket replacement part. Burner is working again.
★★★★★
★★★★★
Greg W - June 9, 2020
Verified Purchase
Easy repair, quick to receive
Came fast. Part was what I needed.
★★★★★
★★★★★
FREDERIC S R - November 30, 2021
Verified Purchase
switch works fine
Although it's a genuine replacement part, it is not the same as what was installed at the factory. Determining the proper terminals for all five wires must be done very carefully, since it is not an exact replacement. As others have noted, the terminal markings can be difficult to see. You will probably need to use the threaded adapter and screws for the shaft to extend the proper distance through the control panel.
★★★★★
★★★★★
Andrew K - May 15, 2018
Verified Purchase
Installation error
Unfortunately part was not exactly like old part therefore wrong connection shorted it out and destroyed part.
★★★★★
★★★★★
Paul S - September 6, 2018
Verified Purchase
Surface Burner switch Replacement
The received part was represented as a replacement for the original part. And while I have not attempted the repair, it does not appear that installation of the shipped part will be sucessful.
★★★★★
★★★★★
Melissa G - March 17, 2018
Verified Purchase
Customer service lacking
I purchased this part for my repair which was delivered without issue. However, when I contacted customer service to ask about returning the item I received zero response. We determined this part alone would not repair the unit after placing the order so I asked to return it. It’s been 5 days with no response and then I got this request for the survey on my purchase.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Burner control failed, needed replacement
Drawings on web site somewhat hard to read, resulting in more disassembly than actually necessary. Turns out, simply removing the threaded plastic securing rings around the bases of the controls frees up the faceplate, and allows access to the phillips screws that hold down the bracket. Then it's a simple matter to rep
... Read morelace the control unit by swapping out the leads one at a time from old to new. Be careful when re-attaching those plastic securing rings, they can cross-thread pretty easily.
Read less
David from AVON, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken burner switch. Would not shut off.
Turn off breaker to the oven. Removed four knows by pulling them up and out. Using either a large flat blade screwdriver or adjustable wrench (depending upon stove top model) remove threaded style holders at each burner switch control to remove the glass clock control top panel. Remove glass panel and note ldgasket position. Place glass p
... Read moreanel on top of stove top on a cloth towel to prevent scratches. Remove 8 screws and remove/lift up burner control assembly. Invert and place on its side to gain access to broken contol switch. Took a picture of wiring and close up off switch to help remember where each wire plugs into switch. Remove 2 Phillips screws from the old switch and remove from panel. Using a flat blade screwdriver gently remove one wire at a time and using knob to orientate the off position of the new switch. Remove each wire one at a time and install on the new switch. Compare numbers on both the old and new switch to assist where each wire goes. The numbers are beside each terminal and using a flashlight and magnifying glass will help making the job easier. DO NOT mix the wires up. Use the 2 longer screws and threaded bracket supplied fasten the new switch to the glass panel. Reinstall the glass panel using the screws removed and thread on clips at each switch and tighten using a large flat blade screwdriver. Be sure to route the wiring to not pinch the wires and install the gasket along the front edge which fills the gap along the burner top and side for a tight seal keeping water and food particles out. The infinite control switch has letters such as H1, H2 etc as the switch fits several models with different wiring diagrams and colours so it's impt to note this when transferring the old wires to the new switch. Also the gasket along the top glass edge ensure to note exactly how it is placed to reinstall to be exact when you reassemble. Replace the 4 control knobs by pushing them on after aligning to fit as they were removed. New switch should be positioned the same as the others with off at the top and a notable click. Be sure to note this when transferring wires from the old to new switch. Turn breaker on. Note: If you have minimal skills this should be left to someone who is an electrician or has repair experience in this field.
Read less
Douglas from PONCE INLET, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad control switch for burner
Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.
Harry from Huntingtown, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
14 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mark
November 4, 2019
One of the switches on my range is not functioning. The switch that I have is 318220080. According to your cross reference at your site, the manufacturer uses 903136-9010 to replace 318220080. However, the pins located in 903136-9010 and in 318220080 are in different location. I cannot figure out which pin in 903136-9010 corresponds to which pin in 318220080? Do you have a diagram showing the mapping of pins between these two parts?
For model number CFES365EC2
Hi Mark,
Thank you for your question. The switch is marked with lettering just as your previous switch was. There should be L1, L2, H1, H2, and P next to the terminals on the switch. The black wires would go to L1 and the red wire would go to L2. The H1 and H2 will go to the elements and the P terminal will have the wire from the indicator light would attach to it. I hope this helps. Thank you and have a great day!
13 people found this helpful.
Was this helpful?
Thank you for voting!
Mehdi
January 14, 2020
I need an infinite switch for above type. Do you have it?
For model number CFES355ES3
Hi Mehdi,
Thank you for your question. There are 2 switches that are listed under your model number. The part number listed under your model number for the 6 inch burner element switch is PS2350013 and the part number listed for the 8 inch burner element switch is PS2350014. We hope this helps. Thank you and have a great day.
Hi William,
Thank you for your question. There is a video on our website that you can reference on how to install the surface burner switch. The stove in the video may not show exactly like the one you have, but it will give you a general idea on how to install the part. You will find the video under part number PS236754. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Marcia
November 6, 2019
The switch on my stove for the back burner doesn't always go off when i switch it off. Sometimes i have to turn it back and forth until it goes off and sometimes it comes back on by itself. So i'm wondering what switch i need to replace?
For model number 79046609500
Hi Marcia, thank you for your question. There are a couple of parts that could cause this issue specifically. You will need a multi meter to be able to test the parts. The first part you will want to check is your radiant element. It should be reading between 0 - 120 ohms to be working correctly. The other part to check would be your infinite (or surface burner) switch. When you remove that part from the appliance, connect each probe from your multi meter to the prongs and then turn the switch to an on position. If you get no continuity then the switch is the issue. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Andrew
February 17, 2018
How do i remove the front panel to access the switch
For model number fes355dbb
Hello Andrew, Thank you for your inquiry. Remove the knobs and supports by pulling them off. You may have to disconnect the switch as well. You should now be able to lift off the outer control panel. Then remove the screws that hold the inner control panel on. You should now be able to access the switches. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Pierre
April 27, 2018
Is this part compatible with my model (790.46703605)?
For model number 790.46703605
Hi Pierre, Thank you for the question. Yes, this switch is compatible with the model number provided. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Alex
October 23, 2019
Would 903136-9010 work to replace the switch indicated as 54a in the diagram?
For model number CFES365EC2
Hi Alex, thank you for your question. No, this part is part 54 in your diagram and different from 54A. I have linked the correct part below for you. Good luck with your repair.
903136-9010 replaces the 318369617 or which one. Thanks
Hello Manfredo, Thank you for the question. The part numbers provided are coming up two different parts. The 318369617 has been replaced by 903136-9030. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Terry
November 16, 2021
My dual burner comes on but stays on high on both elements. What would I need to fix this? Thank you.
For model number CFES365ES4
Hello Terry, Thank you for the question. This would be an indication the Switch, PartSelect Number PS820835 that controls the Element is faulty and will need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
My dual element infinity switch is turning it on and off but don't control hi and low if I replace infinity switch part # 316238201. Will this solve the problem?
For model number Frigidaire Stove CFEF3048LSM
Hello Anand, thank you for contacting us. The dual element switch, part number PS3504401, will be the correct compatible switch to solve your problem. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
