FACEPLATE GRAPHICS (BK) WB27T11005
Fits your JB710SM1SS Range!
★★★★★
★★★★★
Rated by 2 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
24.83
In Stock
Get FREE EconoShip on orders over $100! T&C apply
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your JB710SM1SS Range!
PartSelect Number PS2321447
Manufacturer Part Number WB27T11005
Manufactured by
GE
Troubleshooting
This part works with the following products:
Range.
This part works with the following products:
General Electric.
Customer Reviews
Average Rating:
2 Reviews
★★★★★
★★★★★
5.0
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Robert B - August 13, 2020
Verified Purchase
Looks good
Arrived quickly, haven't installed yet.
★★★★★
★★★★★
Robert M - May 29, 2018
Verified Purchase
Faceplate for Electronic Control Board
Bought the faceplate which greatly simplified the installation of my Electronic Control board which I also bought. Pretty easy repair. Don't try prying off the old one! Oven works like new!
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 2 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Damaged and worn controls faceplate
1. Unplugged power cord.
2. Remove (5) screws securing the top rear access panel.
3. Remove (4) screws securing the clear plastic control board.
4. Peel off the old faceplate.
5. Install new faceplate being careful to align properly.
6. Re-install control board.
7. Re-install rear access panel.
8. Connec ... Read more t power cord and test all controls.
2. Remove (5) screws securing the top rear access panel.
3. Remove (4) screws securing the clear plastic control board.
4. Peel off the old faceplate.
5. Install new faceplate being careful to align properly.
6. Re-install control board.
7. Re-install rear access panel.
8. Connec ... Read more t power cord and test all controls.
Read less
-
Steven from FRANKLINTON, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat, buttons not working, beeping
Turned power off, removed back cover, removed four screws for control board and replaced. The control board shorted out due to accidentally lifting the bottom heating coil while energized. This caused it to short out on the terminals in the back (did not trip breaker for some reason). Removing those connectors to clean them up a little is
... Read more
the only reason I needed the pliers. All the wires are color coded to put them back where they came from on new board. Because of other stories on this web site, I knew to order the $12 faceplate graphics so I didn't have to try to peel off the old one. Unfortunately, the graphic was damaged in shipping. However, I am getting a replacement free of charge, but I have to take it all apart again to stick it on. 1/4" nut driver is really all a person needs to do this job. Pliers could help pull wires off terminals if they are really tight, and the back panel might be secured with one phillips head screw also. Mine wasn't, but it looked like it should have been so it is now. I also put a little electrical tape on the inside of the rear panel behind those connectors for the bottom heating coil, so if it is ever lifted up again, it won't short out and fry the control board again.
Read less
Other Parts Used:
-
Richard from Littleton, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
12 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2321447
Manufacturer Part Number: WB27T11005
Manufacturer Part Number: WB27T11005
Brand
Model Number
Description
Back to Top
FACEPLATE GRAPHICS (BK)
$
24.83
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.