Part Location Diagram of WD12X32799 GE DETERGENT MODULE
See part 811 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

DETERGENT MODULE WD12X32799

 Fits your ZDT925SSN0SS!
★★★★★
★★★★★
2 Reviews

Rated by 1 customer 

A Bit Difficult 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 37.55
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your ZDT925SSN0SS!
PartSelect Number PS17137026
Manufacturer Part Number WD12X32799
Manufactured by GE
Troubleshooting
This part fixes the following symptoms:
Will not dispense detergent
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric.
Part# WD12X32799 replaces these:
WD12X20247, WD12X20391, WD12X21056, WD12X22577, WD12X22578, WD12X23541, WD12X24060, WD12X28240, WD35X21737
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
3.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.8 / 5.0, 1 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
The GE Cafe series Dishwasher not drying dishes.
I pulled the dish washer out and, make sure you turn off the power, disconnect the water and drain line. un screw the mounting screws.
The first thing i checked was the drain filter which was clogged. I took shop vac and sucked all the excess water out and removed the flood switch. seemed ok but you can't tell if its ok, so just replace it. I then removed the door from the unit. I needed to replace the dispenser. After the door was off I tilted the machine forward, to check the heater. I pulled the quick connects off and checked the resistance across the heater, should be 16 ohms mine was 16.3 so heater not bad. looking at the bottom of the machine, follow the left hand wire and it will attach to a thermal overload. (a small round disc which is not listed in the parts manuals ), I checked for continuity across the switch it was open.
On this model GE the switch is resettable, a small reset button in the middle of the overload. I reset it and continuity was restored. only three things might cause this to kick. one the flood switch, the vent fan or the turbidity sensor. I replaced all three and the machine is working great.
If you have replaced your heater and still doesn't heat, try resetting that switch. and give GE a big thank you for not telling any one about the switch.
A big thank you to PartSelect for having all the correct replacement parts.
Other Parts Used:
DETERGENT MODULE VENT FAN Assembly Flood Switch SENSOR TURBIDITY Assembly
  • Gary D. from ALBUQUERQUE, NM
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable)
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brent
December 29, 2023
Getting LD error code. I think it is for leak detection. Not seeing any water leaking but the rinse agent only lasts a couple of days. Could it be a bad detergent module?
For model number PDT785SYN5FS
PartSelect logo
Hi Brent, thank you for reaching out. The Ld error code indicates that the dishwasher is taking longer than normal to drain. We would recommend checking the drain hose for clogging. If the issue still persists, you may need to replace the drain pump, part number PS12743166, to fix the issue. We hope this solves your problem!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS17137026
Manufacturer Part Number: WD12X32799
Brand
Model Number
Description
General Electric
CDT706P2M4S1
Dishwasher
General Electric
CDT706P2M5S1
Dishwasher
General Electric
CDT725SSF0SS
Dishwasher
General Electric
CDT725SSF2SS
Dishwasher - DISHWASHER
General Electric
CDT725SSF4SS
Dishwasher - DISHWASHER
General Electric
CDT725SSF6SS
Dishwasher - DISHWASHER
General Electric
CDT725SSF7SS
Dishwasher - DISHWASHER
General Electric
CDT765SSF0SS
Dishwasher - DISHWASHER
General Electric
CDT765SSF1SS
Dishwasher - DISHWASHER
General Electric
CDT765SSF7SS
Dishwasher - DISHWASHER
General Electric
CDT835SMJ0DS
Dishwasher - DISHWASHER
General Electric
CDT835SMJ2DS
Dishwasher
General Electric
CDT835SMJ4DS
Dishwasher
General Electric
CDT835SMJ5DS
Dishwasher
General Electric
CDT835SSJ0SS
Dishwasher - DISHWASHER
General Electric
CDT835SSJ2SS
Dishwasher
General Electric
CDT835SSJ4SS
Dishwasher
General Electric
CDT835SSJ5SS
Dishwasher
General Electric
CDT836P2M4S1
Dishwasher
General Electric
CDT836P2M5S1
Dishwasher
General Electric
CDT836P3M4D1
Dishwasher
General Electric
CDT836P3M5D1
Dishwasher
General Electric
CDT836P4M4W2
Dishwasher
General Electric
CDT836P4M5W2
Dishwasher
General Electric
CDT855M5N0S5
Dishwasher - Dishwasher
General Electric
CDT855M5N2S5
Dishwasher - Dishwasher
General Electric
CDT855M5N3S5
Dishwasher - Dishwasher
General Electric
CDT855M5N5S5
Dishwasher - Dishwasher
General Electric
CDT855P2N0S1
Dishwasher - Dishwasher
General Electric
CDT855P2N2S1
Dishwasher - Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service