Make sure you haven't got the discount earlier.
CONFIGURED MACHINE CONTROL BOARD WD21X27998
Fits your DDT700SMN0ES!
★★★★★
★★★★★
Rated by 2 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
158.70
In Stock
Get FREE EconoShip on orders over $100! T&C apply
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your DDT700SMN0ES!
PartSelect Number PS16542462
Manufacturer Part Number WD21X27998
Manufactured by
GE
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric.
Part# WD21X27998 replaces these:
WD21X25699, WD21X25992, WD21X25994
Customer Reviews
Average Rating:
1 Review
★★★★★
★★★★★
5.0
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Chuck S - May 10, 2023
Verified Purchase
As advertised
As advertised
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 2 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bad control board caused dishwasher to stop before finishing cycle.
Pretty easy repair for this model dishwasher…
1. Turn breaker for dishwasher off.
2. Remove front lower kickplate.
3. Remove small wire connector from dishwasher door to control board connector on lower right side.
4. remove one screw to remove power wiring junction box cover on lower right side.
5. Remove wire nu ... Read more ts securing dishwasher power wires to incoming power leads.
6. Remove 2 screws holding junction box to dishwasher frame and move out of the way of the plastic control board shroud.
7. Remove screws holding control board shroud and lower control board.
8. Disconnect 3 electrical connectors from board.
9. Remove screw holding control board to shroud.
10. Install new control board into shroud in same orientation, reinstall electrical connectors, reinstall board/shroud assembly, reinstall junction box, reconnect power wires with wire nuts and electrical tape as required, install junction box cover, reconnect door connector to board, reinstall kickplate, turn circuit breaker back on.
1. Turn breaker for dishwasher off.
2. Remove front lower kickplate.
3. Remove small wire connector from dishwasher door to control board connector on lower right side.
4. remove one screw to remove power wiring junction box cover on lower right side.
5. Remove wire nu ... Read more ts securing dishwasher power wires to incoming power leads.
6. Remove 2 screws holding junction box to dishwasher frame and move out of the way of the plastic control board shroud.
7. Remove screws holding control board shroud and lower control board.
8. Disconnect 3 electrical connectors from board.
9. Remove screw holding control board to shroud.
10. Install new control board into shroud in same orientation, reinstall electrical connectors, reinstall board/shroud assembly, reinstall junction box, reconnect power wires with wire nuts and electrical tape as required, install junction box cover, reconnect door connector to board, reinstall kickplate, turn circuit breaker back on.
Read less
-
Travis from NEW MARKET, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would quit after about 3-4 minutes.
Decided it could be 1 of 3 things. Fuse on main circuit board that controls hot water. Main control board or drain pump failure. Was not able to find out how to do diagnostics on this unit as there is no "cycle control" feature and this is a top of the line unit. Replaced the fuse and dishwasher failed. Replaced the circuit board and dish
... Read more
washer failed the first time. Second time it went to completion and has worked properly since. You can go on line and find videos on removing the circuit board for GE dishwashers. This can be done without pulling the dishwasher out. Remove the lower black dust panel and insulation. Remove cover to electrical box - 1 screw and remove. Remove 2 to 4 screw on a sheet metal bracket that holds the circuit board. Notice where 2 metal hangers are located if you remove 4 screws on the left and right side of machine as they drop out. Remove black corded door sensor under circuit board. Work the sheet metal back and forth to remove from dish washer so that circuit board is exposed. Remove circuit board connectors and pull out unit to install new circuit board. Some have one screw and some have only plastic retainers. Re-install. I did not need the drain pump and the circuit board comes with a control board fuse. Washer was only 14 months old and 2 months out of warranty.
Read less
-
Gary from ARLINGTON, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
17 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS16542462
Manufacturer Part Number: WD21X27998
Manufacturer Part Number: WD21X27998
Brand
Model Number
Description
Back to Top
CONFIGURED MACHINE CONTROL BOARD
$
158.70
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.