Average Repair Rating: 4.5 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Pump motor would not start
I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again
Nick from Littleton, CO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
10 of 23 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
February 5, 2018
Dw fills ok then sounds like motor is bound up for a couple seconds then pauses a couple secs. And does this 5 times then pumps water out and stops. I disassembled and made sure chopper spins and spun motor (stuck finger in hole that feeds sprayer) motor spins ok. Is this likely the start capacitor or a control board issue?
For model number Kudc10fxss6
Hi Robert, Thank you for the question. This sounds like an issue with the capacitor.If you have a Multimeter you can test the Capacitor. It will read a resistance reading that will go up very quickly to infinity if it is good. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
EG
January 7, 2019
Machine shut down during wash and no lights or buttons work. Almost as if it has no power. Do have power into the machine.
For model number KUDS35FXSS9
Hello EG, thank you for your question. If the unit stopped during a cycle and the lights and buttons aren't working try unplugging or turning the breaker off to the dishwasher for about 10 minutes to see if that resets the unit. If it still will not power on, you probably have an issue with the electronic control board PartSelect Number: PS3651433. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jimmy
May 15, 2019
The dishwasher will fill with water then you will hear light click as it tries to go to wash then it goes to drain and pumps out the water, the wash cycle never starts, could you advise please and thanks
For model number KUDC10FXWH6
Hello Jimmy, thank you for inquiring. For this symptom you will want to replace the Electronic Control part PS11773157.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Rhys
April 28, 2023
How am I supposed to know which connector on the capacitor is positive? There is no marking?
For model number WPW10334457
Hi Rhys,
Thank you for your question. The capacitor does not have positive or negative terminals. We hope this helps!
Was this helpful?
Thank you for voting!
Blake
August 17, 2023
Unit has power to control board but no water is entering unit. Checked water valve and it is working properly. Checked capacitor on motor and found it bad. Would this have anything to do with no water going into unit? I don’t know the sequence of the operation of the dishwasher.
For model number 66517502200
Hello Blake, thank you for the question. In order for your dishwasher to fill, the water supply valve must be turned to the open position. Locate your dishwasher's water supply under the sink and twist the valve open as needed to allow water to flow freely through the water supply line and into the unit. The capacitor is not the issue for no water entering the unit. We recommend replacing the door switch, part number PS11745501. Good luck with your repair!
I replaced the control board, dishwasher ran good for about 35 minutes then stopped with the normal light flashing. I unplugged the dishwasher and plugged it back in. I pushed the cancel/drain button. The motor starts and the dishwasher starts to drain for about 5-7 seconds then shuts off and the normal light flashes again. Could this be the capacitor?
For model number MDB8959AWS2
Hello Mike, thank you for getting in touch. Yes, the issue could be most probably with the capacitor, part number PS11753080. It helps keep the motor running. You may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
David
April 5, 2018
My kitchen aid dishwasher will not wash. It will fill with water but the jets are not spinning. Then it will drain. There is an ever so slight hum when in the wash cycle. I checked and cleaned the food chopper attached to the circulation pump. I also pulled out the circulation pump to see if anything was wrong. I got a ohm reading of 6 on the motor leads. Anything else that i can check?
For model number KUDP02CRBS1
Hi David, Thank you for the question. It might be an issue with the water level. Start the dishwasher in a regular cycle allowing the dishwasher to fill and wash for a few minutes, open the door and check the water level and temperature in the bottom of the tub. The water level in the center of the tub should be 3/4 to 1 inch deep or approximately 1/4 inch below the bottom of the heater element. The water temperature needs to be 120 degrees on the first fill of the cycle. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
