This bake element is located at the bottom of the oven to supply heat and it has push-on terminals. If your baking element is burnt out, the heat is not consistent, or is defective, then replacing the element could be a solution to your appliance problem. The tools needed for this replacement are: a screwdriver and needle-nose pliers. The first step in is to unplug the range or shut off the house circuit breaker before starting. Unscrew the black of the oven cavity to pull out wires from the defective element. Reconnect wires to the new element and screw it back on. Make sure the element is sitting flat.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Element will not heat | Oven not heating evenly | Will Not Start
Ask our experts a question about this part and we'll get back to you as soon as possible!
30 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
December 8, 2017
I got the new baking element, I connected put back the power but element is not working although the tester shows power on attachment connections.
For model number WFE361LVT0
Hi John, Thank you for the question. If the element tested good and it is not turning on, it sounds like an issue with the Electronic Control Board. This board controls the oven operations and might be defective. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Dave
November 12, 2017
How do you check the bake element to make sure it is bad?
For model number RF265LXTT0
Hi Dave,
Thank you for your question. You will have to remove the element from your appliance. You would test your element with a multi meter to check to see if it is working correctly. This element should show a reading between 0 and 50 ohms of resistance. I hope that helps. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Jennell
November 14, 2019
Will product number wpw10308477 be compatible with rf303pxkq?
For model number RF303PXKQ
Hello Jennell, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Manufacturer Part Number WPW10308477. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mary
November 22, 2019
How wide is the element?I
For model number WPW10308477
Hi Mary, it is almost 21 inches wide. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Josephine
May 20, 2019
My oven has stopped heating completely, neither the bottom element nor the broil element even get warm. Is it possible to repair the problem? Thank you.
For model number 1RE32303
Hello Josephine, thank you for inquiring. For this symptom you will want to replace either the Safety Thermostat part PS11740991 or the Oven Sensor part PS11749737. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Pat
November 4, 2019
What is the wattage of the bottom oven element of my range?
For model number AER5844VCS0
Hi Pat,
Thank you for your question. The bake element is 2400 Watts. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
CLIFFORD
November 8, 2019
The lower and upper heating elements will not heat up ! All of the numbers and buttons on the cercuit board seam to work just fine
For model number RF265LXTB3
Hello Clifford, thank you for your question. The most likely issue is a bad electronic control board PartSelect Number: PS11728037. However, we would recommend testing the sensor first, as this could also cause that issue. If the sensor is fine, the board should be replaced. The sensor is PartSelect Number: PS11749737. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Terry
January 21, 2020
This is a Whirlpool baking element h*ow do i attach to my oven
For model number Rf364lxmt0
Hello Terry, thank you for your question. The bake element is PartSelect Number: PS11752501. There is an installation video at the link for this part. Here is the link that will provide the installation instructions.
https://www.partselect.com/PS11752501-Whirlpool-WPW10308477-Oven-Bake-Element.htm?SourceCode=4&SearchTerm=RF364LXMT0&ModelNum=RF364LXMT0
1 person found this helpful.
Was this helpful?
Thank you for voting!
Earl
December 22, 2019
Can this part be picked up in houston,texas today?
For model number Wpw10308477
Hello Earl and thank you for writing.
No, sorry we are selling online only and shipping to customers, we do not have any storefronts. We hope this helps. Please contact us anytime.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sylvain
April 8, 2022
I need the baking element my stove model is werp4110sb and my element : connection 1.75 inch wide approx. 20.5 inch and depth 16 inch approx. I think the real part number is PS11752501 thanks
For model number WERP4110SB0
Hello Sylvain, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11752501. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Part Videos
Replacing your Whirlpool Range Oven Bake Element
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 25 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The large top burner and the oven bake burner elements as well as the oven light had all burned out
I looked up a how to video on You Tube which I watched and then ordered the appropriate parts which I installed as soon as they arrived. Problem solved.
1. Unplug the power 2. Unscrew the two screws that hold the element 3. Pull the element out a little to expose the wires. 4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN. 5. Firmly seat wires back onto new element and replace screws 6. Bake stuff!
Matthew from MIDDLETOWN, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
Jenny from GREENFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element died
Followed instructions on urine that you provided. Instructions were great. Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.
Jill from LYNNWOOD, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat up.
Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.
Johnie from PARKERSBURG, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element, broken
Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers. Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Frank from COLUMBIA, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom element stopped working
Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.
ArLinda from ALTON, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake Element Does not Heat
I installed th for a refue Temperature Sensor and that was the fix. I did not need to install the bake element. I returned the bake element
use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.
Joyce from BALLWIN, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
73 Reviews
4.8
Filter By Rating:
5 Stars
65
4 Stars
6
3 Stars
1
2 Stars
1
1 Star
0
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Philip D - July 23, 2023
Verified Purchase
Worked as expected
The oven element fit my oven as expected. It was really simple to install and it works great.
★★★★★
★★★★★
Larry W - January 16, 2023
Verified Purchase
easy repair
the part was in great condition and got the part fast. it took me about 5 minutes to put it in and know the stove works great again.
★★★★★
★★★★★
Sandra M - December 19, 2022
Verified Purchase
Fixed the problem!
I appreciate the ease in which I was able to resolve the issue of getting the appliance up and running!
Thank you.
★★★★★
★★★★★
Chiquita H - December 17, 2022
Verified Purchase
Easy repair
Fast service
★★★★★
★★★★★
Gwen D - November 26, 2022
Verified Purchase
Fast & accurate delivery/part
Received the part within a couple of days of ordering. Site was very helpful in finding serial # and exact part needed for my oven. Also helpful with the video on installation. Would definitely use this again
★★★★★
★★★★★
E H B - November 22, 2022
Verified Purchase
Easy to Install, Worked Well,
The order was delivered quickly. It was easy to install. It works appropriately.
★★★★★
★★★★★
Daniel D - November 17, 2022
Verified Purchase
Quality part, easy install
Very good price. Easy and quick to install (I used the video here on the PartSelect website product page). Oven back to working like it should.
★★★★★
★★★★★
Kenneth C - November 7, 2022
Verified Purchase
Perfect fit
Site made it easy to order correct part. Arrived on time in perfect condition.
★★★★★
★★★★★
Todd G - September 26, 2022
Verified Purchase
Working great
Came on time and if I remember right. It came early
★★★★★
★★★★★
Nicole T H - September 5, 2022
Verified Purchase
Easy repair-worked as expected. Video was very helpful and easy to follow
The part shipped in a timely manner. Our oven is working again!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11752501
Manufacturer Part Number: WPW10308477
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
