
Drain Hose
$
53.94
On Order



Get this part fast. Average delivery time via standard shipping: 1.8 days.
PartSelect Number PS11747697
Manufacturer Part Number WP99002652
Manufactured by
Whirlpool
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
Maytag, Jenn-Air, Amana, Magic Chef.
Part# WP99002652 replaces these:
AP6014458, 99002652
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Part Videos
Replacing your Maytag Dishwasher Drain Hose
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 3 reviews.
What's this?
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Cat brought in a mouse that turned into a RAT!
Ist Repaired a hole in a rubber hose under the sink. 2nd Removed the 10 foot drainage hose with a regular screw driver (1 clamp at each end of the hose).
3rd Removed the insulation and replaced with the new after disinfecting the entire top and sides of the dishwasher with bleach. This eliminated all bad odor etc. only had to remove 2 plastic brads, 1 on each side of the unit.
Done and no leaks.
3rd Removed the insulation and replaced with the new after disinfecting the entire top and sides of the dishwasher with bleach. This eliminated all bad odor etc. only had to remove 2 plastic brads, 1 on each side of the unit.
Done and no leaks.
-
Tim from Penn Valley, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
-
16 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drain line had split
disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes
-
William from Interlochen, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
-
Parts Used:WP99002652
13 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The original drain hose developed leak
Pulled dishwasher out far enough to get at the original hose. Disconnected and drained the hose. Connected new hose, zip tied the hose in place, pushed dishwasher back in place and re-anchored. Zippidy do...piece of cake. Perfect fit.
-
Sy from CABLE, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
-
Parts Used:WP99002652
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Filter By Rating:
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Mike L - August 1, 2018

Hose is Too Short!!
Maytag Authentic Part? The drain hose is about 12 to 18 inches shorter than the original drain hose. I had to switch the double sink tail pieces and the drain hose was still barely long enough to reach the new location of the tail piece dishwasher inlet. This resulted in a lot more work to install the hose. The description provided doesn't even state the length of the hose so you are buying it in the blind. All this fun for an exorbitant price of $65. I would have been better of buying a new dishwasher. Buyer beware on this one.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11747697
Manufacturer Part Number: WP99002652
Manufacturer Part Number: WP99002652
Brand
Model Number
Description
