This switch controls the stove top surface burner.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Element will not heat | Will Not Start
This part works with the following products:
Range.
Part# WP9763761 replaces these:
9763761
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dottie S - July 15, 2020
Verified Purchase
Easy to install
Customer service was great helping me figure out which part I needed. Arrived quickly and was easy to install.
★★★★★
★★★★★
Shawn H - November 12, 2018
Verified Purchase
Switch Replacement
OEM replacement part for my KitchenAid Architect Series electric range. Pulled off the 4 burner knob and removed 2 screws to access faulty switch behind control panel. Disconnected both wire harness connectors on faulty switch and removed 2 screws holding in switch. Removed and replaced with new switch. Reversed procedure. Easy!
★★★★★
★★★★★
Francis W D - February 7, 2018
Verified Purchase
OEM part
Exact replacement, original part. When in easy
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Broke the stem so the nob would no longer work
Turned the power power off. unscrewed two screws under the front face plate with the oven door open. Lifted up and over and the front face plate came off. Unscrewed the 2 screws hold the nob in place and disconnected the wires. Screwed the new one in place and connected the wires. Put the face plate back and turned the power back on.
George from BELTSVILLE, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the heating element controls had a few dead spots when setting temperatures
turn off breaker to stove. open oven door and locate two screws that are above the door that hold down the bottom of the front panel. the screws were not common headed but I had some odd ball screw driver heads that fit. the front panel had to be pulled out a little then lifted vertically to unhook it from the lip on the top of the sto
... Read moreve. after removing the knob there are two screws hidden under it that hold the control module too the panel. the light on the front panel can be sli to the side to release it from the panel so that you have more slack to unplug and change the wires from the old control module to the new. screw retaining screws back through front panel to new control module. slide light back onto lens in control panel. hang control panel back on stove and secure with the two screws above the front stove door. press new knob on. turn breakers back on
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Karen
December 21, 2017
I'm having difficulty with the right front knob on my cooktop. The knob itself is very loose and it intermittently would turn on the burner. It doesn't work at all now. I was thinking i need a replacement knob but tried the knob on a different burner and it worked. Do you think i need to replace the ignition switch instead? If so, is this something i could do myself or would you need special tools? Would you need to remove the front panel to install a new switch? Thank you!
For model number KESS907SSS00
Hi Karen,
Thank you for your question. Yes, it would more than likely be you would have to replace your switch behind the know instead. You would have to remove your control panel to get at the switch to remove it and install a new one. You should not need special tools. Perhaps a putty knife and the appropriate screw driver. We do not have installation instructions specifically for this part, however this video should show you how to remove your front control panel so that you can get at your switch to replace it. Here you are: https://youtu.be/u2bLjvkJBg4 . Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Chris
December 14, 2019
Would the 'infinite switch - front right' work for the left side as well? Thanks.
For model number YKERS807SS00
Hi Chris, you would need PS11747407. Thank you for your question and good luck with your repair!
Hello. My wife was using the right front element when she heard a pop from the knob and saw a reddish glow at the edge of the glass stove top. Smoke was coming out of spindle hole of the knob. Turning on the knob now doesn't make the element work and crackling sound/smoke/burning wire smell emits. Would only a replacement knob be the cure?
For model number KESS907SSS
Hello Ted,
Thank you for your question. You would need to replace the right front burner switch under part PS11747406 to fix the element issues. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jorge
September 11, 2021
The small element is not working (not heating), I was told to change the element, I did, still not working, then I was told to change the infinite switch, I did and still not working. What could it be?
For model number YKESS907SS03
Hello Jorge, Thank you for the question. If the Element and Switch were both replaced with OEM parts and did not fix the issue, we suggest checking the wiring to and from the Element. We hope this helps!
Was this helpful?
Thank you for voting!
Carlos
September 23, 2022
Have received replacement part WP9763761 for my Kitchen Aid stove. Can you identify wire connections on back of switch so I can correctly reconnect wires. Line, Load, Pilot. Not identified on back of switch.
For model number WP9763761
Hi Carlos, thank you for reaching out. We have researched your model and attached a relevant video that might help you with replacing the infinite switch. To remember where each wire goes, it's best to take a picture for reference from the old switch before removing it. We hope this is what you were looking for.
For Model #YKESS907SS00. Right Front cook top not working. Opened front panel and found small red indicator was off. I put into the position and now red indicator is on but still not working cook top. Should i order Burner Element of Infinite Switch. ? Glass top built in electric range.
For model number YKESS907SS00
Hello Kimmy, thank you for reaching out. According to our research, we would recommend testing the Burner Element for continuity with a multimeter. If there is no continuity, we would recommend replacing it, the part number is PS11764908. If that does not help, we would suggest replacing the Infinite Switch, part number PS11747406. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Per the Sears Appliance repairman, I need replacement OEM part numbers:
1. 9763761 RF and
2. 9763762 RR
Are your correct replacement part numbers:
1. PS11747406 and
2. PS11747407
Thank you.
Mike
For model number KERS807SBL00
Hi Mike, thank you for your question. Yes the PS part numbers that you have are the correct OEM parts that you need. We hope this helps.
Was this helpful?
Thank you for voting!
Kunal
September 15, 2023
I have KitchenAir smooth top range and the switch for the right front element sometime work and sometimes does not work. I have to keep turning the switch around for it to work .. and while working sometime it gets off itself. (the red indicator light also goes off).
Do I need to replace the switch ?
thanks,
For model number YKERS807SP00
Hi Kunal, thank you for contacting us. Based on our understanding of the issue, we would recommend you to change the infinite switch, part number PS11747406, to fix this issue. The infinite switch turns the surface element on and off and controls how much heat the element produces. Glad to be of assistance!
Was this helpful?
Thank you for voting!
Bill
January 14, 2022
Front right burner will flicker on and off and burner is no longer reliable. This is a glass top unit. Is this a switch issue or are the elements shot?
For model number KESS907SSS04
Hello Bill, thank you for writing. The symptoms you have described point to the switch. We hope to hear from you soon.
