Spark Igniter WP7432P109-60
★★★★★
★★★★★
Rated by 3 customers
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
52.81
On Order
PartSelect Number PS11744544
Manufacturer Part Number WP7432P109-60
Manufactured by
Whirlpool
Product Description
Spark Igniter Specifications
This part creates the spark that lights the gas and starts the burners.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Gas igniter glows | but will not light
This part works with the following products:
Cooktop, Range.
This part works with the following products:
Jenn-Air.
Part# WP7432P109-60 replaces these:
AP6011348, 71002724, 7432P109-60
Customer Reviews
Average Rating:
2 Reviews
★★★★★
★★★★★
5.0
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Horace A - March 11, 2019
Verified Purchase
Replace igniter
I had no problem with the installation because of it was the right part, and was very satisfied
★★★★★
★★★★★
Sam T - March 16, 2018
Verified Purchase
Just a snap
Quick n easy
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 3 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h
... Read more
ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
-
Marlene from Dana Point, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed
took the nuts off &replaced the new ignited
-
Robert from Pleasanton, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not stop igniting even after fire was on
unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove
... Read more
base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install
Read less
Other Parts Used:
-
Bill from Pearland, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Wrench set
19 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744544
Manufacturer Part Number: WP7432P109-60
Manufacturer Part Number: WP7432P109-60
Brand
Model Number
Description
Back to Top
Spark Igniter
$
52.81
On Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.