Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Forrest B - December 24, 2019
Verified Purchase
Works perfectly!
Easy to find part. Works perfectly. I hope it lasts more than a couple of years. That’s why I only give it a 4. I've replaced this exact piece one about 3 years ago. Given that the other three I have are originals, I’d hope this would last more than 5 years.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one.
... Read more Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Read less
Joseph from Lake George, CO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours.
... Read more John, N.J.
Read less
John from Perth Amboy, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that atta
... Read morech to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Read less
Richard from Lansing, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
9 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
two burner ignitors would not function on cook stove
1. ordered two new switches 2. installed switches 3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Warren from Las Cruces, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dennise Marie
February 22, 2018
Is this part compatible with the above make and model stove?
For model number Caloric Oven RMA339-UN
Hello Dennise, thank you for your question. Yes, part number Surface Burner Ignition Switch WP4157180 is the correct replacement part for your appliance. I hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.