Upper Agitator WP3349019 | Official Whirlpool Part | Fast Shipping | PartSelect
Upper Agitator – Part Number: WP3349019
Upper Agitator – Part Number: WP3349019 Upper Agitator – Part Number: WP3349019 Upper Agitator – Part Number: WP3349019 https://partselectcom.azureedge.net/Schematics/Maytag/OBEL0PDR.gif

Upper Agitator

Troubleshooting

This part fixes the following symptoms:

Will not agitate

This part works with the following products:

Washer.

This part works with the following brands:

Whirlpool, Maytag, Roper, Estate, KitchenAid, Crosley, Inglis.

Part # WP3349019 replaces these:

3349019, 3352113, 3357527.
Questions and Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 10 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Eddie from Lovington, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Parts Used:
WP3349019, 285811, 285587
upper agitator not turning
removed agitator top by pulling up with hands. Removed inner agitator seal body by grasping with pliers and pulling up. Used 7/16 socket with extra extension to remove top agitator retension bolt. Removed top agitator body and thrust spacer by lifting off of agitator base. Assembled dogs on body as shown in instructions. Replaced thrust spacer on top of agitator base. Installed upper agitator body. Placed dog body inside upper agitator. Placed small piece of paper over 7/16 socket and forced bolt into socket. This held bolt in upright position as I replaced it down inside the upper agitator body and dog assembly with the long extensions. Replaced O-ring on inner agitator seal body and replaced into the upper agitator body using the long extensions to tap it into place. Pressed top agitator cap onto top of upper agitator body. All done. The agitator repair kit purchased had a thrust spacer in it but was not the correct one for my model so I purchased the correct spacer separate. The website is great because it shows the parts in detail so you can take your time and get the proper parts first time, everytime.
42 of 1076 people found this instruction helpful.
Was this instruction helpful to you?
Mark from Long Valley, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WP3349019, 285811
Cloths mover was worn out
1st removed the cap, then took nut drive/ long socket and removed the agitator nut. Pulled up and removed the agitator / cloths mover. With a gentle pull and twist the cloths mover separated from the agitator. The old dog assembly fell out in the process. Installed new dog kit in agitator and put new cloths mover on the agitator. Put back in machine and tightened nut. Your web site is great . Easy to navigate and understand. Parts shipped same day and were at my house the next day. Great Prices and also found the live chat useful. Will sure to use again.
For this repair I do recommend replacing both the dogs and the cloths mover as the slots in the cloths mover do wear.
39 of 41 people found this instruction helpful.
Was this instruction helpful to you?
Caven from Richmond, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Parts Used:
WP3349019, 285811
Upper agitator wore out
Pull the cap off of the top of the agitator.
Pull the plastic peice that is inside of the agitator up.
Use a deep well socket with an extension and remove the nut.
Pull the agitor off.
Follow the installation instructions that come with the part.

I saved $40 on the cost of the parts and the price to repair, which would probably cost about the same as the part I would have picked up at the local supplier. ~$90.

This is the first time I used the site. Two thumbs up. The price is right and the delivery is fast.
20 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Michael from El Segundo, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Parts Used:
WPW10074580, WP3355758, WP3349019, 285811
Top portion of agitator wouldn't turn.
First I removed the top cap on the agitator, then I removed the second cap inside the agitator. I moved the agitator with my hands and saw that the "dog ears" were worn and no longer touched the agitator and couldn't move it. I then used a nut driver to remove the nut that held the top portion of the agitator onto the bottom portion. I made a note of the worn parts, got online at PartsSelect.com and ordered the replacement parts. A few days later the parts arrived and I repeated the above process in reverse using the new parts. It now works like new!!! It wasn was very easy. Thanks!!!
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Joshua from Lincoln, NE
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Parts Used:
80040, WP3349019
Replacement of upper agitator.
Very simple. Remove the fabric softener dispenser. Then remove the nut that is inside the agitator (requires a couple of extensions for your socket set). Remove the agitator by pulling up.

I replaced the 'dog ears' or agitator and the upper agitator. It is easy to see where everything needs to go after you take it apart. The upper agitator had plastic gears that were stripped and wouldn't have worked by only replacing the directional cogs.

Its easy, nothing to worry about.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
danny from WASHINGTON, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
80040, WP3349019, 285587
agitator would not
took off bolt holding agitator on... replaced parts..put back on
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
James from Oxford, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Parts Used:
WP3349019, 285811, 285587
all went well. all parts were perfect
remove top with screwdriver. used coat hanger to remove upper seal and cap. removed screw with nutdriver and extension and rachet. installed new parts and reversed procedure. Partselect.com is great.
1 person found this instruction helpful.
Was this instruction helpful to you?
XAVIER from RIO RICO, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
80040, WP3349019, 285811, 285587
Washing machine would not agitate.
I used a socket wrench to remove the bolt holding the agitator assembly together. Removed the assembly and replaced Upper Agitator, Agitator Agitator Repair Kit with new parts using the instructions enclosed. I did purchase extra Agitator Directional Cogs and a thrust spacer to have as spare. It was so easy a caveman can do it ;)
1 person found this instruction helpful.
Was this instruction helpful to you?
Randy from Mills, WY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
WPW10072840, WP358237, WP3349019, 285811, 285587
this unit was not agitating
I removed the center bolt that holds it in place.Removed the old agitating unit and installed the new parts. Very simple.I was more then happy with the ordering and repairing.I will deffinetly use this system again
1 person found this instruction helpful.
Was this instruction helpful to you?
Jack from Dallas, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
WP3349019, 285811, 285587
Upper Agitator not working properly, noisey.
Bottom Agitator was working, but top part wasn't. It was running ok, but not cycling the clothes from top to bottom.
The repair was fairly simple. I took the cap off the center, and down inside was a domed looking disk with an O ring on it. I turned it a little to unseat it, and it came right out. I used a Socket wrench with an 11mm socket and multiple extentions to reach down to the bolt. When I took out the bolt, the whole thing comes out. I got the top agitator piece, it needed one. the repair kit, it needed this also. And a thrust washer that I did not need. The kit came with a thrust washer, and I didn't know it. The washer only cost $2 and something, so I didn't worry about it to much. Had all the instruction, with pic's, so it was no problem to replace. Anyone with a little mechanical know-how will breeze through it.
0 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
2 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11741161
Manufacturer Part Number: WP3349019
Brand
Model Number
Description
Whirlpool
1CLXR7244PT0
Washer - Residential
Whirlpool
1CLXR7244PT1
Washer - Residential
Whirlpool
2DLXR7244MQ0
Washer - Residential
Whirlpool
2DLXR7244MQ1
Washer - Residential
Whirlpool
2DLXR7244MQ2
Washer - Residential
Whirlpool
2DLXR7244MQ3
Washer - Residential
Maytag
2DMTW5705TW0
Washer - Residential
Maytag
2DMTW5705TW1
Washer - RESIDENTIAL WASHER
Whirlpool
2DWTW5305SQ0
Washer - Residential
Whirlpool
3LBR5132AN0
Washer
Whirlpool
3LBR5132AW0
Washer
Whirlpool
3LBR5132BW0
Washer
Whirlpool
3LBR5132BW1
Washer
Whirlpool
3LBR6132EQ0
Washer
Whirlpool
3LBR6132EQ1
Washer
Whirlpool
3LBR7132DW0
Washer
Whirlpool
3LBR7255AN0
Washer
Whirlpool
3LBR7255AQ0
Washer
Whirlpool
3LBR7255BQ0
Washer
Whirlpool
3LBR7255BQ1
Washer
Whirlpool
3LBR8255DQ0
Washer
Whirlpool
3LBR8255EQ0
Washer
Whirlpool
3LBR8255EQ1
Washer
Whirlpool
3RLBR8543JQ1
Washer - Residential
Whirlpool
3RLBR8543JQ2
Washer - Residential
Whirlpool
3RLBR8543JQ3
Washer - Residential
Maytag
3UMTW5755TW0
Washer - Residential
Maytag
3UMTW5755TW1
Washer - AUTOMATIC WASHER
Whirlpool
3XLBR5432JQ1
Washer - Residential
Whirlpool
3XLBR5432JQ2
Washer - Residential