Average Repair Rating: 5.0 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
When right hand door was opened first, and then left hand door, the mullion rail did not move all the way to the "open" position so that if the left hand door was closed after the right hand door the rail would bang against the right hand door and not close all the way until manually pushed into pos
Remove the existing mullion rail:
- Remove the screw from the center hinged cover. - Remove the mullion rail by pushing upward. The top and bottom hinges slide over tabs attached to the door. I had to bump it gently from underneath. - Disconnect the three wire connector that's underneath the center hinged cover.
... Read more Install the new mullion rail by reversing the above steps: - Connect the three wire connector and snap it into its holder. - Slide the new part over the top and bottom hinges. Be sure that all three hinges are correctly lined up before sliding the rail over the tabs. - Push it down far enough that the hole for the screw in the center cover is lined up with its corresponding receptacle in the door. - Replace the screw.
Read less
Michael from FALLBROOK, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff
October 3, 2017
How do I replace the vertical mullion rail ? Thanks !!
For model number JFC2089WEM
Hi Jeff, Thank you for the question. First you will need to remove the one screw in the center, When you open the doors you will see around the middle of the rail where it attaches to the door. Next slide the rail up to remove. Then remove the wire connector. Reverse the steps to install the new Rail. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
December 24, 2019
What is the overall length of this mullion? Thank you.
For model number WP12722803AP
Hello Mike,
Thank you for your question. The dimensions of the mullion are approximately 37 inches by 3 inches. We hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jan
July 16, 2019
Is item #6 in the door diagram the part that flips closed? Ours sticks open when we close the door and condensation gets on the outside of the door.
For model number MFF2558VEM5
Hi Jan,
Thank you for your question. Yes, part number 6 in the diagram is the mullion that flips closed when you close the doors. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Andrew
September 23, 2019
When i shut the left door of the fridge (this is the one with the mullion) the right door pops open. Often times we do not notice that the right door is open a the fridge keeps running. This just started happening recently. Is there a remedy of a part that can fix this problem?Thanks. Andrew
For model number GX5SHDXVY04
Good Day Andrew. Thank you for your question in regards to your unit (Model Number GX5SHDXVY04). We would recommend examining your fridge to see if any any of the shelves or bins are not properly installed or if they may have been knocked off their alignment. This could cause your door to be forced open after you closed it. Hope this helps. Best Regards.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Margie
July 30, 2023
The left side handlebar on the middle door of this Fridges screw is loose.
For model number WRX735SDBM00
Hello Margie, thank you for reaching out. According to our research, there is a set screw at the front bottom of the handle. You have to use an Allen wrench to tight that screw. If it does not help, you may need to replace the door handle, part number PS11723191. We hope this helps!
Center Mullion can detached at bottom hinge How do I get it reattached Do I have to take it all apart and reside the clips back in Only the bottom clip is off
For model number KBFS25EVMS00
Hello Mel,
Thank you for writing in. We have attached a video to show you how to replace the mullion. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
