Part Location Diagram of 134511600 Frigidaire Drive V-Belt
See part 28 in the diagram
Replacing your Frigidaire Washer Drive V-Belt
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Drive V-Belt 134511600

 Fits your EL27M6WXFC!
★★★★★
★★★★★
28 Reviews

Rated by 27 customers 

Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 24.93
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your EL27M6WXFC!
PartSelect Number PS1146950
Manufacturer Part Number 134511600
Manufactured by Frigidaire
Product Description

Drive V-Belt Specifications

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; check your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Washer Drive V-Belt

Replacing your Frigidaire Washer Drive V-Belt
Troubleshooting
This part fixes the following symptoms:
Burning smell | Will not agitate | Spins slowly | Will not drain
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Westinghouse.
Part# 134511600 replaces these:
AP3867042, 1156860, 134511600, 131234000, 131686100, 134161100, 3204418, F145371, F145371-000
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
28 Reviews
4.8
Filter By Rating:
  • 5 Stars
    26
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
  • 3
Customer Repair Stories
 Average Repair Rating: 3.9 / 5.0, 27 reviews. What's this?
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing installation instruction that matched.
Washer pumps and drains but does not agitate or spin.
Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.
  • DENNIS from EATON RAPIDS, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Smell of rubber under dryer. Inspection proved belt cracked and shinny worn spot.
Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.
  • Fred from WOLVERINE, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)
  • Sharon from TEMPLE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drive belt old and stretched
unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.
  • George from Sault Ste. Marie, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor burnt out
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
  • ANNA from STATEN ISLAND, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive Belt Was Noisy-Slipping
I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.
  • Steve from Carrollton, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy operation - "Chugged" during operation.
With prep work mentioned below and a good flashlight it takes about 15 to 30 minutes if you're a good handy-man. If you're not, get a neighbor or friend who is. This repair isn't rocket science, but does take a some mechanical aptitude. This unit is a washer/dryer combo unit. Unplug power cord and remove water supply hoses, the drain hose and dryer vent if required to obtain easy access to front panel. There is water in all the lines, so have some towels and a small gallon bucket to help drain the lines if disconnected. Remove two screws on bottom of front panel. Be sure there is about 2 inches from washer/dryer to floor in front to allow front panel to drop directly down, then pull panel out lightly. Wood spacers or similar are recommended under front feet to prop-up front of washer. (There are two tabs on each side of the front panel. The panel must be pulled straight down to clear tabs). Another option is tilt back the washer/dryer about 60 to 75 degrees unit to make the front panel more accessible if all is disconnected in back and you have the room to do so. Once the front panel srews are removed, you may have to place an object (thin pry bar or screw driver) between the top of the washer unit and the front panel for release (be careful not to dent or scratch the top metal or front panel. Remove front panel and set aside. Locate belt near bottom and tensioner pulley (it moves back and forth laterally), push in tensioner pulley to relieve pressure on belt and remove belt from small pully wheel at motor, then the large drum pulley wheel. Place new belt on large pulley first, then small pulley. Push in tensioner pulley and move middle of belt to the inside of the tension pulley to take up the slack. This process is somewhat hard. It takes good hand strength. Be sure the belt is aligned in pulley grooves. Place washer/dryer back in level position, re-attach water supply hoses, drain hose, dryer vent line and power cord, if removed for repair. Check for leaks in water supply lines and be certain the drain hose is well attached to the drain pipe. (This is a good time to clean or replace the dryer vent line to prevent possible lint fires.) Plug in washer/dryer unit and test as if washing a small load. Re-install front panel after successful test in run operation. The part came quickly and fit perfectly.
  • Peter from Lynnwood, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken belt
I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory
  • odell from Elizabethtown, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Belt
Very easy to install. Unscrew 2 screws and I was done in minutes. Thanks for the fast part delivery!
  • Stephen from Honesdale, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer was not spinning
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
  • Mohamad from Chicago, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

7 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
August 22, 2017
I have order a new v-belt from you today. Part number 134511600 as mine was cracked. I did not see on your home page a video of this installation. Could you e-mail the video. Also, is there a belt dressing that should be applied to the new v belt before installation. Thanks
For model number FEX831CS0
PartSelect logo
Hello Fred, thank you for contacting us. No belt dressing. We have a how to video on our site just below the image, you can also click the link below, hope this helps! http://www.partselect.com/PS1146950-Frigidaire-134511600-Drive-V-Belt.htm#RepairVideo

27 people found this helpful.

Was this helpful?
Thank you for voting!
Elroy
June 25, 2019
What is the size of the drive belt
PartSelect logo
Hello Elroy, Thank you for the question. This belt is 1/2" wide x 32" long.I hope this helps!

19 people found this helpful.

Was this helpful?
Thank you for voting!
Mike
January 11, 2018
In my Kenmore washer dryer combo how do I proceed to change the drive belt in the washing machine
For model number 41794814301
PartSelect logo
Hi Mike, Thank you for the question. You will need to remove the front panel from the washer to access the belt.Once the panel is removed you will be able to see the belt and how it fits onto the pulley. Hope this helps!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Terri
February 26, 2019
Washer squeals at the start of a spin cycle and sweats during agitation. A sign that the belt needs to be replaced?The resident repairman said this washer did not have a belt and that washer needed to be replaced. thanks
For model number GLWS1439FSO
PartSelect logo
Hello Terri, Thank you for contacting us. I suggest checking the following parts: PS1152574 Agitator Drive Block, PS418897 Tension Idler Pulley, and PS815490 2-Speed Motor with Pulley. Have a great day!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Rhea
April 2, 2019
How to change drive v belt on front load machine
For model number FAFW4011LW0
PartSelect logo
Hello, Thank you for the question. Here is a link to the how to video. Hope this helps! https://www.youtube.com/watch?v=L9bfAp5irYs

3 people found this helpful.

Was this helpful?
Thank you for voting!
Joe
April 8, 2019
Is it same for washer&dryer combo
For model number fex831fs1
PartSelect logo
Hi Joe, Thank you for your question. Yes, this belt is listed under your model number and it is designed to work with your washer/dryer combo. I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Melissa
February 26, 2020
My dryer has had a burning smell, washer doesn't always spin, and now neither one will start, but there is power. Do you think this is the drive belt and how many will i need?
For model number FFLE3911QW0
PartSelect logo
Hello Melissa, Thank you for your question. It is likely the belt is causing the symptoms, but it is also possible that the idler arm assembly under part PS11775626 for your model could be causing both the smell and the lack of spinning for the washer as well, so we suggest checking both parts for visible defects. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1146950
Manufacturer Part Number: 134511600
Brand
Model Number
Description
Kenmore
41789980100
Washer Dryer Combo
Kenmore
41789980800
Washer Dryer Combo
Kenmore
41790802990
Washer Dryer Combo
Kenmore
41790802991
Washer Dryer Combo
Kenmore
41790802992
Washer Dryer Combo
Kenmore
41790807990
Washer Dryer Combo
Kenmore
41790812990
Washer Dryer Combo
Kenmore
41790812991
Washer Dryer Combo
Kenmore
41790812992
Washer Dryer Combo
Kenmore
41790814000
Washer Dryer Combo
Kenmore
41790814001
Washer Dryer Combo
Kenmore
41790814002
Washer Dryer Combo
Kenmore
41790817990
Washer Dryer Combo
Kenmore
41790862990
Washer Dryer Combo
Kenmore
41790862991
Washer Dryer Combo
Kenmore
41790862992
Washer Dryer Combo
Kenmore
41790872990
Washer Dryer Combo
Kenmore
41790872991
Washer Dryer Combo
Kenmore
41790872992
Washer Dryer Combo
Kenmore
41791702000
Washer Dryer Combo
Kenmore
41791702001
Washer Dryer Combo
Kenmore
41792702200
Washer Dryer Combo
Kenmore
41793702200
Washer Dryer Combo
Kenmore
41793702201
Washer Dryer Combo
Kenmore
41793802200
Washer Dryer Combo
Kenmore
41793802201
Washer Dryer Combo
Kenmore
41793812200
Washer Dryer Combo
Kenmore
41793812201
Washer Dryer Combo
Kenmore
41793814200
Washer Dryer Combo
Kenmore
41793814201
Washer Dryer Combo
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service