Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the temp was not accurate
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.
First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.
pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Left hand hinge was broken, oven didn’t close properly.
I remove four screws two on the left side and two screws on the right side. I pull the oven out about ten inches, removed two screws that hold the hinge in place, took out the broken hinge and reverse the installation.
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Oven over heat sensor in upper control compartment going off due to circulation fan failure.
Turn power to oven off at the breaker. Remove access panel to upper control panel. With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.
Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.
I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.
False Bottoms in both ovens had aluminum pans melted on them and couldn't be cleaned
Use screwdriver to pull down tab on both hinges. Good hind on door and as you lower to full open door will come off. Pull old bottom, insert new bottom and put door back in slots. Close and then reopen to first position and push tabs back up to lock position
I have a double oven and coincidently I had to replace the two Oven Light Assemblies. I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
The thry was rusty I took the door out And i slide out the thry it's take five minutes I did it by myself now my oven Look like a new I'm so happy now I get the part quickly thank you
Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.
