Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would start and then stop after a few minutes, eventually it completely stopped.
After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.
I input the number into the search box and there was the exact motor I needed.
The correct part showed up in a timely manner and the pricing was very fair.
I disassembled the dryer, removed the old motor and reinstalled the new motor within about 30 minutes.
Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.
I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.
I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.
I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too short belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.
Lint has been bypassing the lint filter and building up in the fan (and duct)
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the parts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.
part of door hinge was worn and allowed door to sag
removed door by undoing screws holding it on dryer. Removed all screws on door EXCEPT the ones with star heads. Separated two parts of door and undid screws holding hinge in place. Removed hinge and replaced with new hinge. Put two faces of door back together and installed door back on dryer.
To be honest and explain, I had previously taken apart the door and removed the star screws which allowed the other pieces of the door holding the window to fall apart. After some difficulty, I was able to put the seal back on and re-install the metal window holders which is why I said it only took 15 minutes after the part arrived and why I accented NOT removing the star screws. There were a couple of other screws which probably didn't need removing but they didn't cause any problem with the installation. After putting the door back on, I had to manually twist the door a small amount because it didn't want to keep the button depressed which kept the motor running which turns the basket and heats the clothes. The door had been causing some trouble for a couple years and we had obviously closed the door with a little extra force when it ''caught'' on the door frame causing it to bend a small amount. It only took one adjustment and worked fine after that.
Loud squealing when the dryer was running...especially on start up.
Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Dryer was very loud and sounded like it was scraping
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
