YKEHS01PMT0 KitchenAid Dryer - Instructions

this belt is too thin for the capacity of this dryer.I had only removed the front panel,replaced the belt and immediately the dryer start.

Watched the tutorial online. Took the back off- replaced the fuse. Put the back on . It was extremely easy !!

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Replace the switch in diagram #4.

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

When the part came in. I unplugged the dryer. Pulled it away from the wall and took the back off. I pulled the wires off the old fuse and plugged them in the new fuse, then unscrewed the on nut that held the old fuse. Then slid the new one in and put the nut back on. Plugged the dryer in and it worked. So I unplugged the dryer and put the back on.

Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.

1) Unplug the dryer. 2) Remove lower front panel, use screw driver to push down then pop the top forward. 3) Heating element is on the right. 1/4 inch nut driver removes front plate and the screws holding the foot in place.4) Remove the two wires connected to the heating element and pull the heater toward yourself 5) Remove the screw next to where the two wires connected to the heater, It takes some effort but it will slide out the heating element. Slide the new element in, put in screw next to terminals, slide heater back into place, put foot screws in, put deflector back on with screw, connect the wires back onto the heating element, put the front cover back on, plug in the dryer and test. It will smell for about a minute being new.

I watched the online video first, which made the removal and installation fast and easy.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

went online to whirlpool typed in my problem and. was directed me to Partselect which said it was thermal fuse and had picture where it was located and how to replace,easy as that.thank you PartSelect.Tim

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.