X8241RV Maytag Cooktop - Instructions

I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.

Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. So I just rested the new one on the old plate.

Pulled each wire slowly out and inserted it onto the new spark module.

Screwed in all the panels back and returned the stove to its proper place.

The range now works as well as the oven, but my broiler still does not light up.

i called PS and to get new knobs--but wait!!!!! i couldnt find a part # for the stove top or the knobs,,the PS agent stayed with me while we browsed the entire inventory,,,we found one that looked like the old ones,,the agent sent it,,,it didnt fit right,,,so i called her again and we found another knob that looked like a proper replacement--IT WORKED,,The PS agent then told me how to return the other knob for a refund,,,The PS agent was outstanding,,,!!!!!!!!!!!!!!!!!!!!!

The repair was a no brainer - twist to release the old burner - disconnect the spark wires. connect the spark wires on the new unit - drop it in and twist to lock - about 2 minute job

I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!

I have a maytag stove and the burner was coroted and it had to be replaced. I went seaching in the Internet for a new stove automatically then I thought maybe I can buy the part so I found this awesome website partselect.com. I was intrigue to see if I can find this part I needed so I put in the model number in an seached and then I placed the order not only for the burner but for the grates as well the website is designed very well! Easy to navigate to find the items your looking for. When I recieved the parts in the mail it took me less than 6 minutes to attach the burner and place the grates on the stove it was a great experience all the way around. I would recommed this web site to anyone.

Note the position of the electrode on the side of the old burner cap. Turn the old burner cap one-eighth turn counter-clockwise to loosen and remove it. Raise the burner cap and disconnect the push-on connector wires from the ground and electrode. Clean the surface and connect the electrode and ground connector wires correctly to the new burner cap and place the burner cap back in the opening, positioning the electrode at the same orientation as it was with the old burner cap. Turn the cap one-eighth turn clockwise until the burner is snug. Turn on the burner control to test that the burner functions correctly. Make sure there is no smell of propane or gas when the burner is not in use which might indicate that the burner is not properly fitted snugly.

Went well

Unscrew the burners an install new ones! Anyone could do this.

I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .

I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd

using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.

The repair was a simple replacement, no tools needed. The old burner and grate came out as easily as the new parts went in. PartSelect Customer Service Rep D. Hanham helped me find and order the correct grate. Great Customer Service!

My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....

part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.

1. Grab the old burner and twist counter-clockwise. 2. Unplug the wire from the old igniter, simply pull off. 3. Take new burner/igniter (this new one comes all-in-one) and reattach the wire to the igniter underneath. 4. Place the burner so the 'nubs' line up with the stove top and then twist clockwise a short amount, it should turn slightly to lock in place. 5. Test. Mine sparked and started better than it has since i have had the stove