WWTR1802KW1 Crosley Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door Handle Broke off
Part arrived in tack.
Removed original screws. Place bottom of handle on sideways then horizontal position.
Next slightly raised top of handle over bump protector. Took orginial screw and screwd Top of door handle into place. Really easy!
Removed original screws. Place bottom of handle on sideways then horizontal position.
Next slightly raised top of handle over bump protector. Took orginial screw and screwd Top of door handle into place. Really easy!
Parts Used:
-
Rosemarie from BOYNTON BEACH, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Parts Used:
-
Alan from SAN MATEO, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom door seal won't seal right
-
MANUEL from LOS ANGELES, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Parts Used:
-
gary from ARANSAS PASS, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It would have been nice to fix item I paid for but I never received it.
I tried contacting this page about the item I never received but I never heard back so this is my review. I DIDNT FIX IT BECAUSE I DIDNT GET ITEM.
Parts Used:
-
Elyse from NEW ORLEANS, LA
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top cools bottom is weak
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
Parts Used:
-
JUSTIN from NEW BRAUNFELS, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Accidentally broke the glass insert.
-
DAVID from SAN FRANCISCO, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken glass on top of crispers
Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.
Parts Used:
-
Teresa from SOUTHFIELD, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door shelf, front rollers cracked
I installed door shelf myself. Very easy. My son and grand did the roller repair. This was fairly easy but the reason I had them do it was to tilt the refrigerator over to reach. Needed man power!!
Parts Used:
-
Pamela from JACKSON, GA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Parts Used:
-
edith from woodbridge, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
8 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom shelf bar broke.
Ordered the part. When it arrived (extremely fast delivery), took the old part off and put the new part in. Perfect fit. Took less than one minute to exchange the old with the new.
Thanks a lot for such a wonderful, pleasant experience. Would heartily recommend your services to anyone in the market.
D. Hall
Thanks a lot for such a wonderful, pleasant experience. Would heartily recommend your services to anyone in the market.
D. Hall
Parts Used:
-
Deborah from Zephyrhills, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the refrig was in storage for about a year, the freezer door warped
removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.
Parts Used:
-
Jeffery from Phillipsburg, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Parts Used:
-
carol from woodland, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
not cooling
removed control unit at top of fridge,that houses light ect.
4 screws,replaced plug in repair part
the $25 dollar part from partselect.com saved me the 270.00 estimated repair charge Quoted by sears
4 screws,replaced plug in repair part
the $25 dollar part from partselect.com saved me the 270.00 estimated repair charge Quoted by sears
Parts Used:
-
Walter from Newcomb, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Parts Used:
-
Bob from Pinole, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!