Models > WU1000 > Instructions

WU1000 Maytag Dishwasher - Instructions

All Instructions for the WU1000
106 - 112 of 112
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door spring broken
once i got it out the spring was a breeze
Parts Used:
Door Spring Kit
  • Richard from Silver Spring, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Belt
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
Parts Used:
Clear Belt
  • WILLIAM from CONNEAUT, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
The dishwasher did not drain
"The order arrived in relatively short order. However, the installation must have been hilarious to any observer. Imagiine an arthritic septuagenerian getting down on the floor and wallowing about fitting a dish washer belt. Hints: 1. Grasp the pulley on the pump with your left hand from under the discharge hose (more room than over the hose) when fitting the belt to the rear of that pulley. 2. Use a hot pad (not an emroidered & quilted one reserved for company) to protect your L forearm from the frame member on the bottom of the machine. Getting up was worse than getting down, but it works! In dishwasher years it's much older than I am."
Parts Used:
Clear Belt
  • Hugh from Avon, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
water leaking at door of dishwasher
based on instructions from previous customers, took off front control and door panel, removed old gasket, replaced new gasket by aligning tabs and pulling through with needle nose pliers, leaking stopped
Parts Used:
Door Gasket - gray
  • JOHN from SLIDELL, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Motor running but no motion or pumping action
Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.
Parts Used:
Clear Belt
  • John from Slidell, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Belt to stiff to roll onto pulley
150 degrees for ten minutes provided enough flexibility to allow the belt to be rolled around the pulley. The machine has been used successfully since installation.
Parts Used:
Clear Belt
  • John from Los Alamos, NM
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
would not drain
The part was a bit difficult to put on and then I discovered that it still would not drain. It turned out that my drain hose was plugged
Parts Used:
Clear Belt
  • Donald from Lake City, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WU1000
106 - 112 of 112
Back to Top