Models > WTW4855HW1 > Symptoms > Will not agitate

Parts That Fix Whirlpool Washer WTW4855HW1 Will not agitate

Will not agitate is a commonly reported symptom for the WTW4855HW1 Whirlpool Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WTW4855HW1 Whirlpool Washer that will fix Will not agitate. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

1 Drive Hub Kit
Fixes Symptom 39% of time
Drive Hub Kit – Part Number: W10528947
★★★★★
★★★★★
25 Reviews

Rated by 15 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This drive hub kit (part number W10528947VP) is for washers. Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to your parts diagram for a complete list of parts included. Unplug the washer before installing this part. Wear work gloves to protect your hands.

$ 33.94
  In Stock
PartSelect Number PS6012095
Manufacturer Part Number W10528947

Replacing your Whirlpool Washer Drive Hub Kit

Replacing your Drive Hub Kit

Customer Repair Stories

Waher would not spin and made noise

Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Read less
  • Andrew from SYLVANIA, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Hub had warn its grooved teeth off and washer wouldnt agitate

ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.
Read less
  • Allison from RICHFORD, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
44 of 57 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Washer Drive Pulley
Fixes Symptom 20% of time
Washer Drive Pulley – Part Number: W10721967
★★★★★
★★★★★
21 Reviews

Rated by 15 customers 

  

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch assembly are stripped and the washer is making noise, or if you are having problems with the wash and spin cycles. You will need to access the bottom of the washer for this repair. It is easiest to if you disconnect your washer from both the water and power source, and lay it on its back. The clutch assembly contains 6 parts, and all are included with the kit. It is also important to change out the entire assembly, rather than individual pieces.

$ 54.38
  In Stock
PartSelect Number PS10057144
Manufacturer Part Number W10721967

Replacing your Whirlpool Washer Washer Drive Pulley

Replacing your Washer Drive Pulley

Customer Repair Stories

Making loud noises.

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
  • Roy from BROOKLYN, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Noise, grinding sounds. Wash tub stopped turning but motor and cycles kept functioning. Process of elimination, must be the clutch assembly.

Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.
  • David from BLOOMINGTON, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
35 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 Washing Machine Upper Agitator
Fixes Symptom 19% of time
Washing Machine Upper Agitator – Part Number: W10836692
★★★★★
★★★★★
14 Reviews

Rated by 1 customer 

  

Very Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

This agitator is for washers. Agitator rotates back and forth to move the clothes inside the tub to clean the load. Unplug the washer before installing this part. Wear work gloves to protect your hands.

$ 97.17
  In Stock
PartSelect Number PS11727882
Manufacturer Part Number W10836692
4 Shift Actuator - 6 Pin
Fixes Symptom 14% of time
Shift Actuator - 6 Pin – Part Number: W10913953
★★★★★
★★★★★
11 Reviews

Rated by 7 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer transmission during the different phases of the wash cycle. This allows the washer to switch between agitating and spinning modes. Signs of a faulty shift actuator include the washer failing to agitate or spin, incomplete cycles where the washer gets stuck in one phase, or unusual noises during operation

$ 66.26
  In Stock
PartSelect Number PS11769864
Manufacturer Part Number W10913953

Replacing your Whirlpool Washer Shift Actuator - 6 Pin

Replacing your Shift Actuator - 6 Pin
5 DRIVE BLOCK RETAINER
Fixes Symptom 3% of time
DRIVE BLOCK RETAINER – Part Number: W11385424

Rated by 1 customer 

  

Very Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

$ 7.16
  In Stock
PartSelect Number PS12728657
Manufacturer Part Number W11385424

Customer Repair Stories

No agitation

Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.
  • Jim from ACUSHNET, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
6 WASHPLATE
Fixes Symptom 3% of time
WASHPLATE – Part Number: W11397111

$ 117.27
  In Stock
PartSelect Number PS12731183
Manufacturer Part Number W11397111
7 Washing Machine Door Lock Assembly
Fixes Symptom 2% of time
Washing Machine Door Lock Assembly – Part Number: W11307244
★★★★★
★★★★★
22 Reviews

Rated by 6 customers 

  

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your washing machine is experiencing issues starting or if the lid is not securing, this lid lock assembly likely needs to be replaced. This lid lock attaches underneath the top portion of your washer and its wire harness connects to the rear of the appliance. To replace this assembly, you will need a screwdriver, flathead screwdriver or putty knife, and wrench. This lid lock is an OEM part that is sold individually and does not come with any other parts or accessories.

$ 139.23
  In Stock
PartSelect Number PS12704713
Manufacturer Part Number W11307244

Replacing your Whirlpool Washer Washing Machine Door Lock Assembly

Replacing your Washing Machine Door Lock Assembly

Customer Repair Stories

FAULTY LATCH-WASHER WOULD NOT GO INTO SPIN MODE

THE NEW LATCH COMES WITH A NEW BEZEL ATTACHED, WHICH MOUNTS TO THE TOP OF THE WASHER, JUST UNDERNEATH THE LID. BECAUSE THE ORIGINAL BEZEL WAS IN PERFECT CONDITION AND DIFFICULT TO REMOVE, I DECIDED TO REMOVE THE BEZEL ON THE NEW LATCH, AND USE THE ORIGINAL ONE. THIS WOULD HAVE TO BE DONE REGARDLESS IN ORDER TO INSTALL THE NEW LATCH. REMOVING THE BEZEL WAS DIFFICULT DUE TO ALL THE LOCKING TABS THAT KEEP IT IN PLACE. I HAD TO RESTRAIN THE SLIDING SWITCH PARTS WHILE I REMOVED TO BEZEL TO AVOID THE ASSEMBLY FROM COMING APART. ONCE I SNAPPED THE NEW LATCH TO THE EXISTING BEZEL, THE ASSEMBLY WORKED FINE. TAKE TIME TO STUDY HOW THE LATCH ASSEMBLY IS ATTACHED TO THE BEZEL SO THAT YOU DON'T BREAK SOMETHING. USE A VERY SMALL SCREWDRIVER TO PRY BACK THE PLASTIC TABS IN ORDER TO RELEASE THE BEZEL FROM THE LATCH ASSEMBLY.
Read less
  • EVAN from STOCKTON SPGS, ME
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

latch switch was not working

unfasten top from back, slide top forward and lift up, remove switch and cable (one piece), in stall new switch and cable, put top down and slide back, reinstall screws.
  • John from BEAVER DAMS, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
26 of 37 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Back to Top