WSSE4220A0AA General Electric Washer - Instructions

Found that the teeth and the agitator coupler hade stripped out. Replaced the coupling and everything worked great. 10 Min and $10. 00 Fixed it up.

There are many on-line videos to help you do this. It's so easy, even a beginner handyperson can do it. For this model, just run a strap under the agitator to assist you in lifting it up off the coupler (good tug). Remove the old worn coupler, put the new one on, set the agitator back on by giving it a little downward push.

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

removed agitator unscrewed agitator coupling replaced with new one replaced agitator

First unplug the washer. When changing the tub straps first remove the magnet switch from the lid. There is a tab at the rear of the switch & then you can bring the switch into the washer & then remove the lid assy. This will save the switch. If you do like I did then you will have to install a new switch because the lid fell & broke the switch. Installing the new switch was fairly easy. Push the tab at the rear of the switch in & push the switch up. I cut the two wires about 3 inches from the old switch & then strip the wires. I installed the two butt connectors before putting the switch in the washer. Then crimp the wires to the corresponding colored wires. Put the front back on the washer.

I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.

Took off old agitator, removed coupling that was bad and put new one on.

The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.

Couldn't get the agitator off by pulling up, then thought about it and got 2 carpenter claw hammers, inserted one on each side and puled up evenly on both and off she came. Sprayed the slots with WD Forty and popped the new on. THANKS saved us a lot of money!!!

We were lucky, the agitator came off on its own. Removed the coupler which cracked when a sheet got stuck underneath it! Replaced coupler and new screw/nut combo, popped on agitator. That easy.

Removed agitator by pulling up, wiggle to and fro, watch out for unexpected release. Agitator coupler was worn, stripped splines. 7\16 socket, long extension to remove bolt in coupler. Install new coupler, new bolt, then line up agitator to splines on agitator coupler and push to snap in place.

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.