WRT8A1EWB Westinghouse Refrigerator - Instructions

took old half off - 2 seconds - put new part in - 10 seconds - DONE!Took longer to get it out of the box than it did to install. Really SIMPLE! Thanks Parts Select!

very easy. took the door off and new strip went on very easily.

I literally just watched the video while I was repairing it at home. This is coming from a very girly girl who was desperate because she did not want to spend money on a new fridge while risking everything to fix it. If I can fix it...anybody can do it! I didn't even use the fancy melting machine, I used regular old wire tape and it is as good as new!

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

I watched the step-by-step installation video and followed the instructions therein.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

I order defrost timer then replaced it but it seemed doesn't work. I order defrost thermostat again then it worked fine until now. Thanks. Part selects.

Snapped the new shelves right in! Awesome - so easy(

I hesitate to say anything since I did exactly what their video told me to do, and it fixed the problem. Couldn't be happier. Was positive I was looking at 1000$ for a new fridge. Love being able to fix it by installing 15$ part myself. Thanks guys.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

First of all I am 78YO, retired. Handy but NOT a handyman. There were two parts to replace. The Defrost Timer was very very easy and went just like the video. 20 minutes at the most. No surprises with only the most basic tools. The Defrost Thermostat was a little trickier. Took about 1 1/2 hours. The Thermostat disconnect plug was not like the video and was stuck hard. Had to use two needle nose pliers to finally get it apart. The rest went OK. The shrink seals were way too large for the job and my Hair Dryer was not able to shrink them enough for a good seal. Used a much smaller shrink seal that a friend had and it worked great. Suggest they use a smaller shrink that works with a hair dryer instead off the blow gun in the video. Wrapped the connection with electrical tape as others have suggested in addition to the Shrink Seal. Went together easy and am very very happy camper. Saved $295 from the Sears Repair Estimate. Dave

It is easier to remove the door, put towels over the goods in the freezer and put the door on a flat surface. Pry up the old gasket gently; it just snaps in, so don't worry. Snap in the new gasket, screw the door back on, and you're set to go. We were scared at first, but it's really a simple operation.

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.

It went very well. Just snap in.

Parts just snap on like Video said